May 1992
INDEX 1
Index
A
AC Voltmeter, 7-2, 7-6, 7-7
Adding Punch In, 2-7
AGFA, 7-8
AMP Section, 2-9, 2-11,
Amplifier Panel, 3-7
AMPEX, 7-8
Attenuation Switch, 2-3
Audio Signal Connection, 2-3
Audio Connector Panel, 3-9, 3-10
Auto Locator, Built- In, 4-11
Auto Locator, CB-119, 8-4
Auto Locator, CB-120, 8-4
Azimuth Adjustment, Repro,7-5
Azimuth Adjustment, Record, 7-9
B
BASF, 7-8
Bias Adjustment, 7-8
Bias Frequency, 8-4
Bottom Cover, 2-9
Brake Torque Adjustment, 6-2
C
Capstan Motor Adjustment, 6-5
Capturing Tape Location, 4-11
Capstan Shaft, 3-2, 5-3, 6-6
Capstan PLL Reference, 2-6
Center Tape Guide, 5-3
CLR Key, 3-4, 4-7, 4-12
Cleaning, 5-3
Connector Pin Assignment, 2-4
CONTROL PCB, 2-6, 2-9, 2-12, 6-5, 6-8
Crosstalk, 8-4
CUE Mode, 4-2, 4-3
Tapping Cue Button, 4-8
Holding Cue Button, 4-8
CUE Button, 3-5, 4-8
D
Damp Setting, 6-5
DC Servo Motor, 3-2
Demagnetizing, 5-2
Depth of Erasure, 8-4
Demagnetizing, 5-2
Dimensions, 8-4
DIN Hub, 4-5
Distortion, 8-4
Dump Edit Mode, 3-5
Dummy Head, 3-6
Dust Cap, 5-4
E
Edge Type, 2-7
EDIT Button, 3-5
EDIT Mode, 4-3, 4-9
EIA Reel, 4-5
Equalizer Change, 2-15
Equalizer Indicator, 3-7
Equalizer Switch, 3-11
Equalization, 8-3
Equalization Adjustment, Repro, 7-7
Equalization Adjustment, Record, 7-11
EQ Indicator, 3-8
Erase Frequency, 8-4
Erase Head, 3-6, 5-3
Exterior View, 1-2
EXT mode, 3-4
F
Fast Wind Mute, 2-6, 4-9
Fast Wind Time, 8-2
Felt pad, 5-4
F.FWD, 1-3, 3-5, 4-2, 4-9
Frequency Response, 8-3
Full Track, 1-2
Full Track Kit, 8-4
Fuse, 2-2, 2-14, 2-15
Fix mode, 2-7,3-4, 6-5
G
Gain, Capstan, 6-5
Ground Terminal, 3-11
H
Heads, 8-2
Head Cover, 6-10
Head Guide, 3-6
Heat Sink, 2-10, 2-12
Head Housing, 5-4
Height Adjusrment, Head, 6-11
I
IEC, 2-15
Input Connectors, 3-9
Input Level, 8-3
Input Transformers, Option, 2-4
Input Level Knob, 3-7, 3-8, 4-7
Input monitor, 4-2, 4-4
J
Jitter, 6-5
To Next Page
Loading...
