REA ScanCheck 3n

To Next Page

To Previous Page

REA ScanCheck 3n

V 1.2.0 24/02/2020

REA VERIFIER

Document change history

Version

Date

Description

Author

1.10

2010-08

Successor version ScanCheck 3n update

S.Liebler

1.20

2019-09-24

Complete rework of the document

S.Liebler

Main Page

Table of Contents4
Introduction to Rea Scancheck 3N8
Scope of Delivery of the REA Scancheck 3N9
Conditions for Transport, Storage and Operation10
Determining the Serial Number on the REA Product12
Safety Instructions13
General Safety Instructions13
Electrical Hazards14
Dangers When Handling the REA Scancheck 3N15
Commissioning the Rea Scancheck 3N17
Hardware Installation17
Charging the Rechargeable Batteries17
Connecting the REA Scancheck 3N to the Mains Power Supply19
Switching on and off20
1> Sleep Mode20
2> Shut down Device20
3> Reboot Device21
4> Terminate GUI21
5> Reboot Verifier21
6> Login / Logout22
7> Save System Information / Device Data to USB22
8> Slide Show22
Switching on Again after a Power Failure22
Changing Pre-Settings on the REA Scancheck 3N23
Standard Parameters for Factory Pre-Settings24
Changing the Menu Language Selection24
Changing Data Output Parameters25
Operating REA Scancheck 3N with Report Printer25
Operating the REA Scancheck 3N with REA Transwin3226
General Information on the Software Installation26
Software Installation28
Software and Device Options29
Updating the Operating Software in the REA Scancheck 3N33
Updating the Device from the USB Stick with GUI34
Updating the Device from the USB Stick with Text Console35
Updating the Device with the Service Tool35
Updating the Device with Transwin3236
Network Installation37
Connection Via "DHCP" Server in the Network37
Direct Point-To-Point Connection38
Connection Via an Ethernet Switch39
Connection with Default IP Address39
Data Connection between the PC and REA Scancheck 3N with an Ethernet Switch40
Setting the Network Addresses40
Setting Directly on the Scancheck 3N Device41
Setting Via Transwin3241
General Information about Network Addresses42
Firewall42
MAC Addresses43
Adjustment and Calibration43
General Information on Adjustment and Calibration43
Adjustment and Calibration Card44
Adjustment of the Measuring Apertures 6, 8 and 10 Mil45
Adjustment of the Measuring Aperture 20 Mil49
Calibrating the REA Scancheck 3N50
Permitted Device Tolerances51
Operating the Rea Scancheck 3N55
Handling the REA Scancheck 3N56
Using the Pressure Plates58
Measuring Bar Codes for the First Time59
Quick Display with LED and Acoustic Signal60
Evaluation According to ISO/IEC1541661
1St Screen Page: Summary61
2Nd to 5Th Screen Page: Deviations61
6Th Screen Page: Optional Parameters62
7Th Screen Page: Error List62
Setting / Selection of the Correct Measuring Aperture63
Measuring Apertures 6, 8 and 10 Mil65
Measuring Aperture 20 Mil (Optional)66
Settings / Button Functions67
General Button Assignments and Control Functions67
Buttons with Special Functions69
Reset Function71
Setup Menu (Pre-Settings Directly in the Device)71
Setup" Main Menu with 6 Sub-Menus71
Setup Sub-Menu <1> Stored Reports72
Set-Up Sub-Menu <2> Adjust/Calibrate72
Set-Up Sub-Menu <3> Settings with 9 Further Sub-Menus72
3> Settings - Sub-Menu <1> Code Type Selection73
Additional Test Criteria74
UPC-A Code - Additional Test Criteria76
UPC-E Code - Additional Test Criteria77
Code 128 / GS1-128 - Additional Test Criteria77
GS1 Databar Code Family79
GS1 Databar / GS1 Databar Stacked - Additional Test Criteria79
GS1 Databar Expanded / GS1 Databar Expanded Stacked - Additional79
Test Criteria80
GS1 Databar Limited - Additional Test Criteria80
The Code 39 Family80
Code 39 / Code 32 - Additional Test Criteria80
Code 39-Full ASCII - Additional Test Criteria (Optional Code Types)82
PZN Codes82
Codabar / Codabar 18 - Additional Test Criteria83
Of 5 Interleaved / ITF-14 Code - Additional Test Criteria83
Of 5 Int IATA / 2 of 5 3 Bar Matrix / 2 of 5 5 Bar Ind - Additional Test Criteria (Optional Code Types)84
Of 5 5 Bar IATA - Additional Test Criteria (Optional Code Types)84
Pharma Code / Plessey Code - Additional Test Criteria (Optional Code Types)85
MSI Code - Additional Test Criteria (Optional Code Types)85
Measuring Program85
3> Settings - Sub-Menu <2> Aperture85
3> Settings - Sub-Menu <3> Evaluation86
3> Settings - Sub-Menu <4> Device Configure with 8 Sub-Menus88
Device Configure <1> Operating System89
Device Configure <2> Output Parameters90
Device Configure <3> Options91
Device Configure <4> Date and Time92
Device Configure <5> Network Configuration92
Device Configure <6> Change Password92
Device Configure <7> Company and User Info93
Device Configure <8> Configure Long Report93
3> Settings - Sub-Menu <5> Code Comparator (Option Only)94
3> Settings - Sub-Menu <6> Article Lookup (Option Only)94
3> Settings - Sub-Menu <7> Factory Reset95
3> Settings - Sub-Menu <8> USB Update95
3> Settings - Sub-Menu <9> Languages95
Set-Up Sub-Menu <4> Edit Document95
Set-Up Sub-Menu <5> Article Selection (Option Only)95
Set-Up Sub-Menu <6> Profile96
Operation with the PC Program REA Transwin3296
Service Tool98
Creating Profiles with the Service Tool98
User Management with the Service Tool99
Simple User Name100
User Management100
Simple Password101
Technical Data Rea Scancheck 3N104
Technical Data, Power Supply Unit104
Terms of Guarantee106
Symbols Used in this Manual106
Appendix107
Abbreviations Used109
Handling109
Obligations of the Operating Company109
Obligations of the User109
Intended Use110
Recycling110
Certificate of Conformity111
Eu Declaration of Conformity112
Certificate of Conformity for Rea Calibration Cards113
Software Update114
Protected Trademarks114
Licence Conditions114
Licence Agreement115
Limited Support and Troubleshooting115
Export Restrictions115
Warning116
Liability116

REA ScanCheck 3n - Page 3

Table of Contents

Other manuals for REA ScanCheck 3n

Related product manuals