Renkforce RF500 Maker Construction Kit

To Next Page

To Previous Page

148

Screw the nozzle to the heating block M6 6 Nm

Clamp the heating cartridge to the heating block M3 1.9 Nm

Screw the nozzle stock to the PEEK part M6 4 Nm

Screw the extruder inlet to the PEEK part M6 4 Nm

Screw the nozzle stock to the heating block M6 4 Nm

Counter the heating block to the hexagon nut M6 4 Nm

Screw the display to the display holder M3 1.7 Nm

Screw the operating knob to the display M3 1 Nm

Screw the display holder to the frame M5 3 Nm

Screw the main PCB to the PCB holder M3 0.3 Nm

Screw the PCB holder to the frame M5 3 Nm

Main Page

Default Chapter2
- Table of Contents2
1 Introduction4
2 Explanation of Symbols4
3 Intended Use5
4 Safety Notes6
- A) General Information6
- B) Mains Unit6
- C) Set-Up, Site of Operation7
- D) Operation7
5 Feature Description8
6 Working Principle of the 3D Printer8
7 Overview of the most Important Parts9
- A) Maker Construction Kit / Construction Kit9
- B) Preassembled Device10
8 Software and Firmware Installation11
- A) Download and Unpacking of the Software/Firmware Package11
- B) General Information on the Repeater Host Software11
- C) Installation of the Repeater Host Software12
- D) Installation and Updating of the Firmware12
9 Required Tools and Material14
10 Assembly of the Mechanical Parts15
- A) General Information15
- B) Assembly of the Components17
11 Mounting of the Electrical Components57
- A) Installation of the Electrical Components57
- B) Wiring of the Electrical Components71
12 Final Work85
13 First Commissioning87
- A) Assembly Of The Filament Holder87
- B) Preparing and Assembling the Printing Plate Support87
- C) Setup and Transport88
- D) Mains Connection and First Activation88
- E) Adjustment of the Motor Driver89
14 Operation at the Printer90
- A) Display and Operating Buttons90
- B) Menu Overview91
- C) Functions of the Individual Menu Items93
15 Calibration95
- A) General Notes on Calibration95
- B) Setting of the Z-Stop96
- C) Heating to Printing Temperature97
- D) Setting the Printing Plate99
16 Inserting, Removing and Changing the Filament100
- A) Inserting the Filament - Mechanical Part100
- B) Inserting the Filament Via the Printer Menu101
- C) Removing and Changing the Filament106
17 First Print of an Example Object from the SD Card107
18 General Notes on 3D Printing110
19 Software "Repetier-Host111
- A) General Notes on Software111
- B) Installation111
- C) Connection of the Connected Printer112
- D) Manual Operation Via the Software114
- E) Placement of a Printing Object in the Software115
- F) Preparation for Print117
- G) Print119
- H) more Detailed Description of the Slicer Functions121
- I) Setting up Another Slic3R Version129
20 Firmware Update132
21 Maintenance135
- A) General Information135
- B) Cleaning135
- C) Nozzle Change136
22 Troubleshooting138
23 Handling140
24 Disposal140
25 Technical Data140
- A) Printer140
- B) Mains Unit140
26 Annex141
- A) Fine Adjustment of the Filament Infeed141
- B) Setup of the Printer Settings144
- C) Recommended Tightening Torque of the Screws147

Renkforce RF500 Maker Construction Kit - Page 148

Table of Contents

Related product manuals