Respironics SmartMonitor2 - Page 38

Respironics SmartMonitor2

80 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Dealer Preparation for Home Setup

32

Table of Contents

Default Chapter3
- Table of Contents3
Introduction7
- Unpacking and Inspection7
- About this Manual7
Warnings and Cautions13
- Warnings13
- Cautions15
How Does the Smartmonitor 2 Work17
- How the Alarms Operate17
- Electrical Ratings18
- Environmental Conditions18
- IEC Classification18
- Symbols Table18
- FCC Part 68 Notice19
- Industry Canada CS-03 Notice20
- FCC Part 1520
Getting to Know the Monitor21
- Smartmonitor 2 Features21
Setting Alarm and Recording Limits25
- Manual Set-Up25
Using Auxiliary Equipment35
- Using the Respironics Model 930 Oximeter35
Dealer Preparation for Home Setup37
Home Setup39
- Step 1: Set the Smartmonitor 2 on a Clean, Flat Surface39
- Step 2: Connect the Patient Cable to the Smartmonitor 239
- Step 3: Connect the Lead Wires to the Patient Cable40
- Step 4: Connect the Lead Wires to the Electrodes40
- Step 5: Attach the Electrodes to the Infant Belt41
- Step 6: Wrap the Electrode Belt Around the Baby41
- Step 7: Connect the Power Cord/Battery Charger44
Responding to Alarms45
- Patient Alarm45
- Testing the Alarm45
- If an Alarm Sounds45
- Responding to System Alarms47
Reducing False Alarms49
Monitoring the Baby51
- Turning the Smartmonitor 2 on51
- Turning the Monitor off - Sibling Alarm51
- If There Is an Internal Software Error, a Special Power off Procedure Is Required51
  - Press and Hold the RESET Button, While Still Holding down the RESET Button Press and Hold the POWER Button. Hold both Buttons down for 5 Seconds51
  - Release POWER Button; Continue to Hold the RESET Button until the Monitor Turns off51
- Monitoring the Baby's Breathing52
  - Respiration Light52
  - Apnea Light52
- Monitoring the Baby's Heart Activity53
Portable Operation of the Smartmonitor 255
- Charging the Smartmonitor 2 Battery55
- Smartmonitor 2 Battery Pack56
Battery Installation Instructions57
Transferring Smartmonitor 2 Information59
- Memory Management in the Smartmonitor 259
  - To Recover the Old Data Using a PCMCIA Card59
  - To Recover the Old Data by Downloading Using Synergy-E59
- Modem Download59
- Transferring Smartmonitor 2 Data to a Memory Card62
- Transferring Smartmonitor 2 Data Using a Computer63
  - Communications Mode Setup63
Caring for the Smartmonitor 265
- Cleaning Instructions65
- Insect Infestation Decontamination Procedures65
- Performing a Functional Self-Test66
- Self-Test Troubleshooting67
Troubleshooting69
Ordering Information71
Glossary73
- Flow Chart of Smartmonitor 2 Parameters75
Appendix A75
Specifications77
Index79

Related product manuals

Preview: Respironics SleepEasy

Respironics SleepEasy

Respironics BiPAP S/T

Preview: Respironics BiPAP Synchrony

Respironics BiPAP Synchrony

Preview: Respironics Wee Sight 1017920

Respironics Wee Sight 1017920

Preview: System One Heated Humidifier

System One Heated Humidifier

Preview: REMstar Auto M Series system

REMstar Auto M Series system

Preview: Respironics EverFlo

Respironics EverFlo

Preview: Respironics 920M PLUS

Respironics 920M PLUS

Preview: Respironics ComfortGel

Respironics ComfortGel

Preview: Respironics Trilogy 100

Respironics Trilogy 100

Preview: Respironics BiPAP Vision

Respironics BiPAP Vision

Preview: Respironics DreamStation Series

Respironics DreamStation Series