Respironics SmartMonitor2 - Page 76

Respironics SmartMonitor2

80 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Appendices

70

Table of Contents

Default Chapter3
- Table of Contents3
Introduction7
- Unpacking and Inspection7
- About this Manual7
Warnings and Cautions13
- Warnings13
- Cautions15
How Does the Smartmonitor 2 Work17
- How the Alarms Operate17
- Electrical Ratings18
- Environmental Conditions18
- IEC Classification18
- Symbols Table18
- FCC Part 68 Notice19
- Industry Canada CS-03 Notice20
- FCC Part 1520
Getting to Know the Monitor21
- Smartmonitor 2 Features21
Setting Alarm and Recording Limits25
- Manual Set-Up25
Using Auxiliary Equipment35
- Using the Respironics Model 930 Oximeter35
Dealer Preparation for Home Setup37
Home Setup39
- Step 1: Set the Smartmonitor 2 on a Clean, Flat Surface39
- Step 2: Connect the Patient Cable to the Smartmonitor 239
- Step 3: Connect the Lead Wires to the Patient Cable40
- Step 4: Connect the Lead Wires to the Electrodes40
- Step 5: Attach the Electrodes to the Infant Belt41
- Step 6: Wrap the Electrode Belt Around the Baby41
- Step 7: Connect the Power Cord/Battery Charger44
Responding to Alarms45
- Patient Alarm45
- Testing the Alarm45
- If an Alarm Sounds45
- Responding to System Alarms47
Reducing False Alarms49
Monitoring the Baby51
- Turning the Smartmonitor 2 on51
- Turning the Monitor off - Sibling Alarm51
- If There Is an Internal Software Error, a Special Power off Procedure Is Required51
  - Press and Hold the RESET Button, While Still Holding down the RESET Button Press and Hold the POWER Button. Hold both Buttons down for 5 Seconds51
  - Release POWER Button; Continue to Hold the RESET Button until the Monitor Turns off51
- Monitoring the Baby's Breathing52
  - Respiration Light52
  - Apnea Light52
- Monitoring the Baby's Heart Activity53
Portable Operation of the Smartmonitor 255
- Charging the Smartmonitor 2 Battery55
- Smartmonitor 2 Battery Pack56
Battery Installation Instructions57
Transferring Smartmonitor 2 Information59
- Memory Management in the Smartmonitor 259
  - To Recover the Old Data Using a PCMCIA Card59
  - To Recover the Old Data by Downloading Using Synergy-E59
- Modem Download59
- Transferring Smartmonitor 2 Data to a Memory Card62
- Transferring Smartmonitor 2 Data Using a Computer63
  - Communications Mode Setup63
Caring for the Smartmonitor 265
- Cleaning Instructions65
- Insect Infestation Decontamination Procedures65
- Performing a Functional Self-Test66
- Self-Test Troubleshooting67
Troubleshooting69
Ordering Information71
Glossary73
- Flow Chart of Smartmonitor 2 Parameters75
Appendix A75
Specifications77
Index79

Related product manuals

Preview: Respironics SleepEasy

Respironics SleepEasy

Respironics BiPAP S/T

Preview: Respironics BiPAP Synchrony

Respironics BiPAP Synchrony

Preview: Respironics Wee Sight 1017920

Respironics Wee Sight 1017920

Preview: System One Heated Humidifier

System One Heated Humidifier

Preview: REMstar Auto M Series system

REMstar Auto M Series system

Preview: Respironics EverFlo

Respironics EverFlo

Preview: Respironics 920M PLUS

Respironics 920M PLUS

Preview: Respironics ComfortGel

Respironics ComfortGel

Preview: Respironics Trilogy 100

Respironics Trilogy 100

Preview: Respironics BiPAP Vision

Respironics BiPAP Vision

Preview: Respironics DreamStation Series

Respironics DreamStation Series