Why does my Ricoh K-C1 All in One Printer show TD sensor initial setting error?
A TD sensor initial setting error on your Ricoh All in One Printer means the TD sensor initial setting is not performed correctly. This could be due to: * A defective ID sensor * No developer * The drum not turning * The development roller not turning * A poor connection of the PCU * The voltage not being applied to charge roller
What to do if Ricoh K-C1 has a charge roller current leak?
If your Ricoh All in One Printer detects a charge roller current leak, it means a current leak signal for the charge roller is detected. This could be due to a damaged charge roller, a defective high voltage supply board, or a poor connection of the PCU. Check these components.
How to fix laser synchronization error in Ricoh All in One Printer?
A laser synchronization error on your Ricoh All in One Printer means that the main scan synchronization detector board cannot detect the laser synchronization signal for more than 5 consecutive 100 ms intervals. This can be caused by: * A poor connection between the LD unit and the BICU board * A damaged cable between BiCU and LD unit * An LD unit out of position * A defective LD unit * A defective BiCU board
What causes Ricoh K-C1 All in One Printer to display TD sensor error?
If your Ricoh All in One Printer displays a TD sensor error, it means the TD sensor outputs less than 0.2 V or more than 4.0 V 10 times consecutively during copying. This could be due to an abnormal TD sensor or a poor connection of the PCU. Check these components.
What to do if Ricoh K-C1 All in One Printer shows a main motor lock?
If your Ricoh All in One Printer displays a main motor lock, it means a main motor lock signal is not detected for more than 7 consecutive checks (700 ms) after the main motor starts to rotate, or the lock signal is not detected for more than 7 consecutive checks during rotation after the last signal. This could be due to too much load on the drive mechanism or a defective main motor. Check these components.
What causes Ricoh K-C1 All in One Printer to have fusing low temperature error?
A fusing low temperature error in your Ricoh All in One Printer indicates that a fusing temperature of lower than 100°C is detected for 1 second by the fusing thermistor during operation or stand-by mode. This could be due to: * An open fusing lamp * A defective fusing thermistor * A defective power supply board * An open fusing thermistor * An open fusing thermostat
What causes a polygonal mirror motor error in Ricoh K-C1 All in One Printer?
A polygonal mirror motor error in your Ricoh All in One Printer indicates that the polygon mirror motor does not reach operating speed within 10 seconds after the motor ON signal is sent, or does not turn on within one of the 200 ms check intervals during operation. Possible causes include: * A defective polygon mirror motor * A poor connection between the polygonal mirror motor driver and the BiCU board * A damaged cable between BiCU/IOB and polygonal mirror motor driver * A defective BiCU board
How to resolve communication error between BiCU and fax controller on Ricoh All in One Printer?
A communication error between the BiCU and fax controller on your Ricoh All in One Printer means the BiCU board cannot communicate with the fax controller. This could be due to a poor connection between the BiCU board and the fax controller, a defective BiCU board, or a defective fax controller. Check the connections and the boards.
How to fix communication error between BiCU and printer controller in Ricoh K-C1?
If your Ricoh All in One Printer shows a communication error between the BiCU and the printer controller, it means the BiCU board cannot communicate with the printer controller. This may be due to a poor connection between these components, a defective BiCU board, or a defective printer controller. Ensure the connection is secure, and check the boards.
Why does my Ricoh All in One Printer show a fusing temperature warm-up error?
A fusing temperature warm-up error on your Ricoh All in One Printer indicates that the fusing temperature did not reach 80°C within 30 seconds after the main switch was turned on. This can be caused by: * A defective or out of position fusing thermistor * An open fusing lamp * An open fusing thermostat * An open fusing thermofuse * A defective power supply board You should inspect these components.
General| Max Resolution (BW) | 1200 x 1200 dpi |
|---|---|
| Grayscale Depth | 8-bit |
| Functions | Print, Copy, Scan |
| Scan Type | Flatbed |
| Media Type | Plain, Envelope |
| PC Connectivity | Yes |
| Connectivity | USB 2.0 |
To Next Page