30
SAVE CHANGES ?
ESC/ENT
5.Press <ENTER> to confirm the copying.
12.7.Creating a record
The record consists of conected programs
You can create up to 100 records with a maximum of 50 programs each.
Creating a record is simply a matter of assigning each step a previously recorded program number.
1.Press <ESC> several times until the display shows the initial screen.
2.Press <MENU> and use <UP>,<DOWN> to scroll to the "Make Record" menu and press <ENTER>.The
following messages appears:
MAKE RECORD
Record: 001 Record No.1
FREE Record status: FREE......the record was not edited
USED......the record steps have assigned programes
3.Use <UP>,<DOWN> or Pan wheel to select desired free record .All LEDs of the PROJECTOR
SELECTbuttons,which have been assigned to the projectors, shine.
Now you have to determine the projectors, which will be used in the record - the mask.Press the PROJECTOR
SELECT buttons matched to the projectors ,which you don´t want to use in the record(their LEDs become off).
Only those projectors will be active in the record where the PROJECTOR SELECT button LEDs shine.
If you wish to create record for previously defined group of projectors,press <NEXT/GROUP>,select desired
group (1-20) by pressing the respective PROJECTOR SELECT button.If you select more than one group,the last
selected group will be active only.The selected group of projectors can be expanded/reduced by pressing the
respective PROJECTOR SELECT buttons.
Note:The record should be created with a maximum of active projectors (in run mode,you can simply reduce the
number of active projectors).
Press <ENTER> and the following screen appears:
Step: 01 Prog: 01 Record step(1-50) and assigned program(1-50,End)
Start step: 01 Step from which the assigned program will start running
Rec.tim: 50.00 Total record time (in seconds) from first step to current step (included)
Fati: 01 StTi: 01 Fati=Fade time multiplier (0.1-9.9 ) , StTi=Step time multiplier (0.1-9.9)
Note:01 means 0.1 ; 99 means 9.9
Note:The projectors used in this record should be used in the programs which you will assign:
Example:
Projectors mask
in the created record: Projector No.1 Projector No.2 Projector No.3 Projector No.10
Projectors mask
in the program No.1 Projector No.1 Projector No.2 Projector No.3 Projector No.10
These projectors will not be active
Projectors mask during record running:
in the program No.2 Projector No.1 Projector No.2 Projector No.6 Projector No.15
4.Fill the items on the screen.
1.Use <UP>,<DOWN> to select the desired record step.
2.Press <RIGHT> and use <UP> , <DOWN> or TILT wheel to assign the program No. (1-50).
3.Press <RIGHT> and use <UP> , <DOWN> to select starting program step.
4.Press the <FADE TIME> (its LED shines) and adjust the fade time multiplier with FADE TIME slider(0.1-
9.9).Press the <FADE TIME> again (its LED is off).
5.Press the <STEP TIME> and adjust the step time multiplier with the STEP TIME slider (0.1-9.9).Press
the <STEP TIME >again.
E.g.If you have adjusted fade time multiplier=5,the assigned program will have the fade time at all steps 5
times longer
If you have adjusted step time multiplier=3,the assigned program will have the step time at all steps 3
times longer.
6.Press <LEFT> and use <UP>,<DOWN> to select the next record step and repeat steps 1-6 in this point.
Note: By pressing <NEXT/GROUP> the current record step is copied to the next step.
To Next Page
Loading...
