R
EGULAR
M
EMORY
C
HANNEL
O
PERATION
Memory Bank Operation
Memory Bank Assignment
1. Recall the memory channel to be assigned to a Memory Bank. Memory channels
L1
/
U1
~
L50
/
U50
(band/scanning limit memories) may not be assigned to a Memory
Bank.
2. Press and hold in the [
SCAN
(
SEL
)] key for 1/2 sec-
ond, then rotate the
DIAL
knob to select the Memory
Bank you want as the Memory Bank for this channel
(“
BA NK1
” ~ “
BANK20
” ).
3. Press and hold in the [
V/M
(
MW
)] key
for 1/2 second to lock in the selected
Memory Bank, then press the [
V/
M
(
MW
)] key momentarily to copy the
memory channel data into the Memo-
ry Bank.
1) You may assign one memory channel into several Memory Banks.
2) The PMS memory channels (L1/U1 through L50/U50) may not be assigned
to a Memory Bank.
Memory Channel
CH 000 145.000 MHz
CH 001 145.500 MHz
CH 002 435.000 MHz
CH 003 435.500 MHz
CH 004 145.800 MHz
CH 005 436.000 MHz
CH 006 128.800 MHz
CH 997 145.620 MHz
CH 998 436.780 MHz
CH 999 128.600 MHz
Memory Bank “5”
Air Band Channels
Memory Bank “4”
Club Channels
Memory Bank “3”
All Amateur Band Channels
Memory Bank “1”
144 MHz Amateur Band Channels
Memory Bank “2”
430 MHz Amateur Band Channels
R
EGULAR
M
EMORY
C
HANNEL
O
PERATION
Memory Bank Recall
1. Set the radio to the Memory mode by pressing the [
V/M
(
MW
)] key, if necessary.
2. Press and hold in the [
SCAN
(
SEL
)] key for 1/2 sec-
ond, then rotate the
DIAL
knob to select the Memory
Bank (“
BANK 1
” ~ “
BANK20
”).
3. Press the [
BAND
(
SET
)] key momentarily to lock in the selected Memory Bank.
4. In the Memory Bank mode of operation, you can only select memory channels within
the current Memory Bank.
5. To change the Memory Bank to another Bank, press and hold in the [
SCAN
(
SEL
)]
key for 1/2 second; now rotate the
DIAL
knob to select the new Memory Bank, then
press the [
BAND
(
SET
)] key momentarily to lock in the new Memory Bank.
6. To exit from Memory Bank operation, press and hold
in the [
SCAN
(
SEL
)] key for 1/2 second, then rotate
the
DIAL
knob to select “
NOBANK
;” now press the
[
BAND
(
SET
)] key momentarily.
Deleting a Memory Channel from a Memory Bank
1. In the Memory Bank mode, recall the memory channel to be deleted from the Memo-
ry Bank.
2. Press and hold in the [
SCAN
(
SEL
)] key for 1/2 second, then press and hold in the
[
V/M
(
MW
)] key for 1/2 second. The channel will now be deleted from the Memory
Bank, but the memory register itself will still be available in the non-Bank mode.
Memory Only Mode
Once memory channel programming has been completed, you may place the radio in a
“Memory Only” mode, whereby VFO operation is impossible. This may be particularly
useful during public-service events where a number of operators may be using the radio
for rst time, and ultimate simplicity of channel selection is desired.
To place the radio into the Memory Only mode:
1. Turn the radio off.
2. Press and hold in the [
MHz
(
PRI
)] key while turning the radio on.
3. Rotate the
DIAL
knob to select the (
F - 6 M- O NLY
)
option, then press and hold in the [
BAND
(
SET
)] key
for 1/2 second.
To return to normal operation, repeat the above steps.
To Next Page
Loading...
