Network setup_ 35
1. Press Menu on the control panel.
2. Pre
ss the up/down arrow to highlight Information and press OK.
3. Pre
ss the up/down arrow to highlight Configuration and press OK.
The machine prints the Con
figuration Report.
Using this Con
figuration Report, you can find your machine MAC address
and IP address.
For example:
• MAC
Address: 00:15:99:41:A2:78
• IP Addre
ss: 192.0.0.192
Setting IPv4 address
You must set up an IPv4 address for network printing and management. In
most cases a new IP address will be automatically assigned by a DHCP
(Dynamic Host Configuration Protocol) server located on the network.
If you use IPv6 address, refer to "IPv6 Configuration" on page 38
In a few situations the IP address must be set manually. This is called a
static IP and
is often required in corporate Intranets for security reasons.
• DHCP IP a
ssignment: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Configuration Report as explained above. If
the report shows that the IP address has changed, the assignment was
successful. You will see the new IP address in the report.
• St
atic IP assignment: Use the SetIP program to change the IP address
from your computer. If your machine has a control panel, you can also
change the IP address using the machine's control panel.
In an office environment, we recommend that you contact a network admin-
istrator to set this address for you.
IPv4 setting using control panel
1. Connect your machine to the network with a network cable.
2. Tu
rn on the machine.
3. Press Menu o
n the control panel.
4. Press the
up/down arrow to highlight Network and press OK.
5. Press the
up/down arrow to highlight TCP/IP (IPv4) and press OK.
6. Press the
up/down arrow to highlight Set IPv4 Address and press
OK.
7. Press the
up/down arrow to highlight Manual and press OK.
8. Enter the
IP address using numeric keypad and press OK.
9. In th
e same way, enter other parameters such as Subnet Mask and -
Gateway and
press OK.
10. After enterin
g all parameters, press Stop/Clear to return to the ready
mode.
Now go to "Installing network connected machine’s driver" on page 36.
IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Configuration Report.
For using SetIP program, disable the co
mputer firewall before continuing
by performing the following:
1. Op
en Control Panel.
2. Dou
ble click Security Center.
3. Cli
ck Windows Firewall.
4. Disab
le the firewall.
Installing the program
1. Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2. Sta
rt a web browser such as Internet Explorer and open the X drive.
(X represents your CD-ROM drive.)
3. Doub
le-click Application > SetIP.
4. Doub
le-click Setup.exe to install this program.
5. Click OK. If necessa
ry, select a language from the drop-down list.
6. Fol
low the instructions in the window and complete the installation.
Starting the program
1. Connect your machine and the computer using network cable.
2. T
urn on the machine.
3. From th
e Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
4. Click on the
icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine’s new information into the configuration window
as follows:
• MAC Address: Find the machine’s MAC address on the Config-
uration Report
and enter it without the colons. For example,
00:15:99:29:51:A8 becomes 0015992951A8.
A MAC address is a hardware serial number of the machine’s
network interface and can be found in the Configuration
Report.
• IP
Address: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192
.168.1.X. (X is number between 1 and 254 other than
the computer’s address.)
• Su
bnet Mask: Enter a new Subnet Mask for your machine.
• Default Gateway: Ent
er a new Gateway for your machine.
6. Click Apply,
and then click OK. The machine will automatically print
the Configuration Report. Confirm that all of the settings are cor-
rect.
7. Click Exit to close the SetIP prog
ram.
8. If necessary,
restart the computer’s firewall.
IPv4 setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
The path and UIs may differ by Mac OS version. Refer to the Mac
OS manual to turn firewall off.
1. Open System Preferences.
2. Click Secu
rity.
To Next Page
Loading...
