Sel SEL-351S - List of Tables

Date Code 20080103 Instruction Manual SEL-351S Relay
List of Tables
Table 1.1 SEL-351S Models .................................................................................................................. 1.2
Table 1.2 SEL-351S Firmware Versions................................................................................................ 1.3
Table 2.1 Options and Explanations for the User-Configurable Front-Panel Labels........................... 2.13
Table 2.2 Communication Cables to Connect the SEL-351S to Other Devices .................................. 2.24
Table 2.3 Output Contact Jumpers and Corresponding Output Contacts ............................................ 2.45
Table 2.4 “Extra Alarm” Output Contacts and Corresponding Controlling Jumpers.......................... 2.45
Table 2.5 Required Position of Jumper JMP23 for Desired Output Contact OUT107 Operation
(Models 0351Sx1, and 0351SxY) .................................................................................... 2.45
Table 2.6 Password and Breaker Jumper Positions for Standard Relay Shipments............................. 2.46
Table 2.7 Password and Breaker Jumper Operation ............................................................................ 2.46
Table 2.8 EIA-232 Serial Port Voltage Jumper Positions for Standard Relay Shipments ................... 2.46
Table 2.9 Jumper Positions for Breaker OPEN/CLOSE Indication..................................................... 2.47
Table 2.10 Jumper Positions for Arc Suppression ................................................................................. 2.47
Table 3.1 Available Phase Time-Overcurrent Elements....................................................................... 3.17
Table 3.2 Phase Time-Overcurrent Elements Settings......................................................................... 3.17
Table 3.3 Phase Time-Overcurrent Element (maximum phase) Logic Outputs .................................. 3.19
Table 3.4 Neutral Ground Time-Overcurrent Elements Settings......................................................... 3.23
Table 3.5 Residual Ground Time-Overcurrent Elements Settings ....................................................... 3.25
Table 3.6 Negative-Sequence Time-Overcurrent Elements Settings .................................................. 3.26
Table 3.7 Voltage Values Used by Voltage Elements........................................................................... 3.28
Table 3.8 Voltage Elements Settings and Settings Ranges (Wye-Connected PTs).............................. 3.29
Table 3.9 Voltage Elements Settings and Settings Ranges (VS Channel) ........................................... 3.29
Table 3.10 Voltage Elements Settings and Settings Ranges (Delta-Connected PTs)............................. 3.30
Table 3.11 Synchronism Check Elements Settings and Settings Ranges .............................................. 3.36
Table 3.12 Frequency Elements Settings and Settings Ranges.............................................................. 3.51
Table 3.13 Sag/Swell/Interruption Elements Settings (must first set ESSI = Y) .................................. 3.56
Table 3.14 Single-Phase Power Element Settings and Setting Ranges (EPWR = 1, 2, 3, or 4) ........... 3.59
Table 3.15 Three-Phase Power Element Settings and Setting Ranges
(EPWR = 3P1, 3P2, 3P3, or 3P4) ..................................................................................... 3.59
Table 4.1 LOP Logic Inputs................................................................................................................... 4.1
Table 4.2 Load-Encroachment Settings Ranges..................................................................................... 4.5
Table 4.3 Available Ground Directional Elements............................................................................... 4.11
Table 4.4 Best Choice Ground Directional™ Logic............................................................................ 4.11
Table 4.5 Ground Directional Element Availability by Voltage Connection Settings ......................... 4.13
Table 4.6 Directional Control Settings Not Made for Particular Conditions....................................... 4.40
Table 4.7 Overcurrent Elements Controlled by Level Direction Settings DIR1–DIR4
(Corresponding Overcurrent Element Figure Numbers in Parentheses............................ 4.40
Table 4.8 z Constant for Z2R Setting................................................................................................... 4.43
Table 4.9 z Constant for Z0R Setting................................................................................................... 4.48
Table 4.10 Affect of Global Settings VSCONN and PTCONN on Petersen Coil Directional
Elements ........................................................................................................................... 4.56
Table 5.1 SEL-351S Front-Panel Target LED Definitions and Settings.............................................. 5.32
Table 6.1 Relay Word Bit and Front-Panel Correspondence to Reclosing Relay States ..................... 6.15
Table 6.2 Reclosing Relay Timer Settings and Setting Ranges ........................................................... 6.17
Table 6.3 Shot Counter Correspondence to Relay Word Bits and Open-interval Times ..................... 6.20
Table 6.4 Reclosing Relay SEL
OGIC Control Equation Settings......................................................... 6.21
Table 6.5 Example Open-Interval Time Settings ................................................................................. 6.25
Table 7.1 Correspondence Between Local Control Switch Positions and Label Settings..................... 7.6
Table 7.2 Correspondence Between Local Control Switch Types and Required Label Settings........... 7.7
Table 7.3 Definitions for Active Setting Group Indication Relay Word Bits SG1–SG6 ..................... 7.19
Table 7.4 Definitions for Active Setting Group Switching SEL
OGIC Control Equation
Settings SS1–SS6 ............................................................................................................. 7.19
Table 7.5 SEL
OGIC Control Equation Settings for Switching Active Setting Group Between Setting
Groups 1 and 4..................................................................................................................7.21