On-Screen Display Menu
CH Setup
If
initial setup does not memorize
all
the channels
in
your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection
is
made
with your
TV
when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all
channels viewable
in
the set area.
CH Memory: You can select the channels
to
skip
in
each
ANALOG
(Air),
ANALOG (Cable), DIGITAL
(Air)
and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
IVV·)
Off:
Does not skip channels. (Channel selection enabled using
CH/VV·)
Remove Scrambled CH: This function makes the TV
look for and then delete digital cable channels that
are scrambled and so unavailable
in
the set area. The
process may take more than 20 minutes.
Yes:
Starts
to
remove scrambled channels.
No:
This function does not work.
mm
• See "Initial Setup" on page 14 for setting each item.
•
If
no channel
is
found, confirm the type of connection made
with your TV and try channel search again.
•
If
you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Antenna Setup-DIGITAL
In
order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna Setup-
OIGITAL" screen.
If
necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is
displayed. The signal information
is
based on the
current channel.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal
is
strong enough for each
channel.
• This function
is
available for DIGITAL
(Air)
only.
Input Skip
This setting allows you to skip the HOMI or PC-IN Input
("Input 4
(PC)",
"Input 5
(HOM!)",
"Input 6 (HOMI)",
"Input 7
(HOM
I)"
, "Input 8
(HOMI)"
and "Input 9
(HOMI)")
on the Input Selection operation.
Yes: Skips the input.
No: Does not skip input.
Input Label
Lets you set the input terminal displayed when using
the INPUT SOURCE menu
or
channel display. Press
Ji./'Iff
/
....
/~
to select the new name for the input
mode.
mm
• You cannot change labels if the INPUT SOURCE
is
TV.
@-24
Auto Sync.
(for Analog PC Input
Mode
Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
mm
• When Auto Sync.
is
successful, "Completed" displays.
If
not, Auto Sync. failed.
• Auto Sync. may
fail
even if "Completed" displays.
• Auto Sync. may
fail
if the computer image has low
resolution, has unclear (black) edges, or
is
moved while
executing Auto Sync.
• Be sure to connect the
PC
to
the TV and switch
it
on before
starting Auto Sync.
Fine Sync.
Ordinarily you can easily adjust the picture
as
necessary
to
change image position using Auto Sync.
In
some cases, however, manual adjustment
is
needed
to optimize the image.
H-Pos.: Centers the image by moving it
to
the left or
right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
mm
• For resetting
all
Fine
Sync. adjustment items
to
the factory
preset values, press
~f~
to select "Reset", and then press
ENTER.
•
It
is
not necessary
to
adjust the "Clock" or "Phase" when a
digital signal
is
being input, so
it
cannot be selected.
• The default cursor position may not be
in
the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
To Next Page
Loading...
