Other Viewing Options
Presetting
Remote
Control
Function
Operating
the
Connected Equipment
To operate the connected equipment, press
FUNCTION to select the
LED
for your device.
(VCR,
AUDIO,
CBUSAT
(cable converter) or DVD.) The
LED
lights up, and the remote control unit button will
function as follows.
• When you operate VCR or DVD, press
INPUT
to select the
terminal connected
to
your device.
• CABLE and SAT cannot be selected at the same time.
1 SOURCE POWER
• Turns the connected equipment power on and off.
2~
• Rewinds the tape and allows picture search.
(VCR)
• Hold down to go
in
reverse.
(DVD)
3 REC
• Starts recording.
(VCR)
4
......
• Pressing quickly once takes you
to
the start of the chapter
currently playing. Each time you press
it,
you move back
to
the start of the previous chapter,
(DVD)
50-9
(CBUSAT), •
(DOT)
(SAT)
• Press a button (or buttons) that corresponds to the
channel that you wish to watch.
6~
• Starts playback.
(VCR,
DVD)
7~~
• Rapidly advances the tape and allows picture search.
(VCR)
• Hold down
to
fast forward.
(DVD)
811
• Sets pauses and still pictures.
(VCR,
DVD)
9.
• Stops the tape transport.
(VCR)
• Playback stops when pressed. With some
DVD
players,
pressing the button twice may open the disc tray.
(DVD)
10
~
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead
to
the
start of the next chapter.
(DVD)
11
FLASHBACK
• Press
to
switch between the current channel and the
channel you were watching immediately before. Some
manufacturers
do
not preset FLASHBACK.
(CBl)
12
CH/\/V
• Press
CH/\
or
CHV
to
tune
in
to a higher or lower
channel.
(CBl)
• Press to select the channel of the
TV
tuner on the VCR,
(VCR)
13
MENU
• When this button is pressed, the
DVD
menu will display.
14
A/T/~/~,ENTER
• J•
.IT
/
....
/~:
Press the button
to
select items on the SAT
GUIDE screen or SAT MENU screen. (SA1). Press the
button to select items on the
DVD
MENU screen.
(DVD)
• ENTER: Press
to
activate the selected function.
(SAT,
DVD)
"
TV
TV VCA AUDIO
I
goo 0
~p.
eBl/SAT
DVD
FUNCTION
,0
0 0 •
SOURCE
LIGHT
I
1
II
•
•
rn
6
2
•
•
•
II
7
II
REC
II
3
II
•
•
•
II
8
4
•
1\1
~
II
9
I
10
•
5
•
•
•
• •
•
•
•
@)
I U
FL~BA.CK
oe
11
VOl
CH
III
12
POWER
SAVING
MUTE
@ - 0
13
14
4
After registering the code, the
LED
will stop blinking
then turn off after one second.
(If
you perform
an
incorrect operation, the
LED
will blink quickly then
turn off.)
AQuas
3 Press
0-9
to enter the manufacturer code.
(See
page 33.)
• Preset mode
is
finished once the
lED
no longer lights
up.
2 After the LED for your device lights up, press
FUNCTION and DISPLAY at the same time
to
enter the code registration mode. The
LED
will
blink.
Presetting
manufacturer
codes
1 Press FUNCTION until the
LED
for your device
lights up.
You can operate the connected
AV
products
(A
V
receiver, cable box, SAT tuner,
DTV,
VCR,
DVD,
LD)
using the presetting manufacturer function of your
remote control unit.
@-
32
To Next Page
Loading...
