What does F0070 CB setpoint fault mean on a Siemens MICROMASTER 430?
The F0070 CB setpoint fault on your Siemens Inverter indicates that there are no setpoint values from the CB (communication board) during telegram off time. To resolve this, check the CB and communication partner.
How to fix Siemens DC Drives motor that fails to run after changing parameters?
If your Siemens DC drive motor won't run after you've changed the parameters, try this: First, set P0010 = 30, then P0970 = 1, and press the P button to reset the inverter to its factory default parameter values. Alternatively, use a switch between terminals 5 and 9 on the control board. The drive should now run to the defined setpoint by analogue input.
What to do if my Siemens Inverter displays F0002 OverVoltage?
If your Siemens Inverter is showing an F0002 OverVoltage error, it means the DC-link voltage (r0026) is exceeding the trip level (P2172). To fix this, verify that the supply voltage (P0210) is within the limits specified on the rating plate. Also, ensure the DC-link voltage controller is enabled (P1240) and properly parameterized. The ramp-down time (P1121) should match the inertia of the load, and the required braking power must be within specified limits.
What to do if my Siemens MICROMASTER 430 Inverter displays F0003 UnderVoltage?
If your Siemens Inverter displays the error F0003 UnderVoltage, it indicates that the main supply has failed. To address this, check that the supply voltage (P0210) is within the limits indicated on the rating plate. Also, ensure that the supply is not susceptible to temporary failures or voltage reductions.
How to troubleshoot F0004 Inverter Over Temperature on a Siemens MICROMASTER 430?
To troubleshoot an F0004 Inverter Over Temperature error on your Siemens Inverter, check if ventilation is adequate. Ensure the fan turns when the inverter is running and that the pulse frequency is set to the default value. Also, verify that the ambient temperature is not higher than specified for the inverter.
What to do if the Siemens Inverter motor fails to start after changing parameters?
If the motor fails to run after changing the parameters on your Siemens Inverter, set P0010 = 30, then P0970 = 1, and press P to reset the inverter to the factory default parameter values. Alternatively, use a switch between terminals 5 and 8 on the control board; the drive should then run to the defined setpoint by analogue input.
What does F0022 Powerstack fault mean on a Siemens Inverter and how to fix it?
The F0022 Powerstack fault on your Siemens Inverter is a hardware fault (P0947 = 22 and P0949 = 1) caused by events such as DC-link overcurrent, short circuit of chopper, earth fault, or I/O board not properly inserted. Check the I/O board to ensure it is fully pressed home.
What to do if Siemens Inverter motor fails to start when the ON command has been given?
If the motor fails to start when the ON command has been given to your Siemens Inverter, check that a valid ON signal is present. Also, verify that P0700 = 2 (for digital input control) or P0700 = 1 (for BOP-2 control). Finally, ensure that the setpoint is present (0 to 10V on Terminal 3) or that the setpoint has been entered into the correct parameter, depending upon the setpoint source (P1000).
What does Siemens MICROMASTER 430 error F0051 Parameter EEPROM Fault mean?
The F0051 Parameter EEPROM Fault on your Siemens Inverter indicates a read or write failure while saving a non-volatile parameter. To resolve this, try a factory reset and new parameterization. If the issue persists, consider changing the drive.
What does F0020 Mains Phase Missing mean on a Siemens MICROMASTER 430 Inverter and how to fix it?
If your Siemens Inverter displays the error F0020 Mains Phase Missing, check the input wiring of the mains phases.
General| Power Range | 7.5 kW to 250 kW |
|---|---|
| Voltage Range | 380V to 480V |
| Frequency Range | 0 Hz to 650 Hz |
| Protection Class | IP20 |
| Input Frequency | 47 Hz to 63 Hz |
| Digital Inputs | 6 |
| Cooling Method | Forced-air cooling |
| Communication | USS |
| Protection Features | Overvoltage, undervoltage, overcurrent, short-circuit, ground fault, overtemperature |
| Analog Inputs | 2 |
| Digital Outputs | 3 |
| Analog Outputs | 2 |
| Ambient Temperature | -10°C to +50°C |
| Control Type | Sensorless vector control |
To Next Page
