Siemens MICROMASTER 430 - Commissioning with CANopen

5 System parameters
MICROMASTER 430 Operating Instructions
72 6SE6400-5AC00-0BP0
ParNr ParText Default Level DS QC
r2845 BO: NOT-Q RS-FF 2 - 3 - -
P2846[2] BI: RS-FF 3 0:0 3 CUT N
r2847 BO: Q RS-FF 3 - 3 - -
r2848 BO: NOT-Q RS-FF 3 - 3 - -
P2849 BI: Timer 1 0:0 3 CUT N
P2850 Delay time of timer 1 0 3 CUT N
P2851 Mode timer 1 0 3 CUT N
r2852 BO: Timer 1 - 3 - -
r2853 BO: Nout timer 1 - 3 - -
P2854 BI: Timer 2 0:0 3 CUT N
P2855 Delay time of timer 2 0 3 CUT N
P2856 Mode timer 2 0 3 CUT N
r2857 BO: Timer 2 - 3 - -
r2858 BO: Nout timer 2 - 3 - -
P2859 BI: Timer 3 0:0 3 CUT N
P2860 Delay time of timer 3 0 3 CUT N
P2861 Mode timer 3 0 3 CUT N
r2862 BO: Timer 3 - 3 - -
r2863 BO: Nout timer 3 - 3 - -
P2864 BI: Timer 4 0:0 3 CUT N
P2865 Delay time of timer 4 0 3 CUT N
P2866 Mode timer 4 0 3 CUT N
r2867 BO: Timer 4 - 3 - -
r2868 BO: Nout timer 4 - 3 - -
r2870 CO: ADD 1 - 3 - -
P2869[2] CI: ADD 1 755:0 3 CUT N
r2872 CO: ADD 2 - 3 - -
P2871[2] CI: ADD 2 755:0 3 CUT N
r2874 CO: SUB 1 - 3 - -
P2873[2] CI: SUB 1 755:0 3 CUT N
r2876 CO: SUB 2 - 3 - -
P2875[2] CI: SUB 2 755:0 3 CUT N
r2878 CO: MUL 1 - 3 - -
P2877[2] CI: MUL 1 755:0 3 CUT N
r2880 CO: MUL 2 - 3 - -
P2879[2] CI: MUL 2 755:0 3 CUT N
r2882 CO: DIV 1 - 3 - -
P2881[2] CI: DIV 1 755:0 3 CUT N
r2884 CO: DIV 2 - 3 - -
P2883[2] CI: DIV 2 755:0 3 CUT N
r2886 BO: CMP 1 - 3 - -
P2885[2] CI: CMP 1 755:0 3 CUT N
r2888 BO: CMP 2 - 3 - -
P2887[2] CI: CMP 2 755:0 3 CUT N
P2889 CO: Fixed setpoint 1 in [%] 0 3 CUT N
P2890 CO: Fixed setpoint 2 in [%] 0 3 CUT N
www.eltra-trade.com
+421 552 601 099
info@eltra-trade.com