EasyManua.ls Logo

Siemens PGC 302 Edition II - Pcpu-2

Siemens PGC 302 Edition II
248 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
PCPU-2
The adjacent drawing shows the standard setting of a
PCPU-2 when delivered. You need only make changes
in the following cases:
If TTY interfaces are to be active (seldom the case),
change X8 to X11
If several chromatographs are used in the Chrom-
LAN network, change station x1/x16
If the chromatograph is not the last participant in
the RS485 ChromLAN network, change X6 or X7.
Meaning of control elements
Station x1 + x16 Participant number in ChromLAN network,
Standard is number 1
X6
X7
X8+X9
X10+X11
J1
RS485 terminator for SER.3
RS485 terminator SER.4
TTY active/passive for SER.1
TTY active/passive for SER.2
Only for test purposes
Further information
Setting instructions for the eight DIP switches, the jum-
pers X6 to X11 and the two station switches can be
found Register 3: ChromLAN networks with TTY and
ChromLAN networks with RS485. Useful information
on troubleshooting on the PCPU-2 can be found in
Register 2: Problems and faults.
Pin assignments of
interfaces SER. 1 to SER. 4
Pin number on 9-pin plug of
PCPU-2 for
Standard Signal SER.1 SER. 2 SER. 3 SER. 4
RS232 GND
TxD
RxD
CTS
DCD
RTS
1
2
3
5
1
2
3
5
1
2
3
5
6
7
1
2
3
5
6
7
TTY TxD -
TxD+
RxD -
RxD+
6
7
8
9
6
7
8
9
RS485 A
B
8
9
8
9
Voltage +5V4444
Factory setting without control software:
Interface Standard Transmission rate
SER. 1
SER. 2
SER. 3
SER. 4
RS232
RS232
RS232
RS232
9600 baud
9600 baud
9600 baud
38400 baud
DIP switches
Switch On/off Meaning
DIP 1
DIP 1
OFF
ON
SER.2 9600 baud
SER.2 4800 baud if TTY
38400 baud if RS232
DIP 2
DIP 2
OFF
ON
SER.2 TTY
SER.2 RS232
DIP 3
DIP 3
OFF
ON
SER.1 Local printer
SER.1 ChromLAN
DIP 4
DIP 4
OFF
ON
SER.1 TTY
SER.1 RS232
DIP 5,6,7 No significance
DIP 8
DIP 8
OFF
ON
Normal mode
PCPU in programming mode
Jumpers
Interface Jumper
SER. 1
SER. 1
SER. 2
SER. 2
Sender
Empfänger
Sender
Empfänger
X8
X9
X10
X11
aktive
11
passive
SER. 2
SER. 1
SER. 3
SER. 4
DIP
X6
X7
X 9
X 8
X11
X10
ON
18
Station x1
Station x16
switch
J 1
PCPU-2 interface Jumpers
SER. 3
SER. 4
X6
X7
with without terminating resistor
1 1
Control electronics
9STEUER.CHP, Stand 20.05.94
11

Table of Contents

Related product manuals