A.8 Information List
551
7SA522 Manual
C53000-G1176-C155-3
189 Error Board 7 (Error Board 7) Device OUT ON
OFF
* * LED BO 135 177 1 Yes
190 Error Board 0 (Error Board 0) Device OUT ON
OFF
* * LED BO 135 210 1 Yes
191 Error: Offset (Error Offset) Device OUT ON
OFF
* * LED BO 135 191 1 Yes
192 Error:1A/5Ajumper different from
setting (Error1A/5Awrong)
Device OUT ON
OFF
* * LED BO 135 169 1 Yes
193 Alarm: NO calibration data avail-
able (Alarm NO calibr)
Device OUT ON
OFF
* * LED BO 135 181 1 Yes
194 Error: Neutral CT different from
MLFB (Error neutralCT)
Device OUT ON
OFF
* * LED BO 135 180 1 Yes
195 Failure: Broken Conductor (Fail
Conductor)
Measurem.Superv OUT ON
OFF
* * LED BO 135 195 1 Yes
196 Fuse Fail Monitor is switched
OFF (Fuse Fail M.OFF)
Measurem.Superv OUT ON
OFF
* * LED BO 135 196 1 Yes
197 Measurement Supervision is
switched OFF (MeasSup OFF)
Measurem.Superv OUT ON
OFF
* * LED BO 135 197 1 Yes
203 Waveform data deleted (Wave.
deleted)
Osc. Fault Rec. OUT_
Ev
ON * * LED BO 135 203 1 No
273 Set Point Phase L1 dmd> (SP.
IL1 dmd>)
Set Points(MV) OUT on
off
* * LED BO 135 230 1 Yes
274 Set Point Phase L2 dmd> (SP.
IL2 dmd>)
Set Points(MV) OUT on
off
* * LED BO 135 234 1 Yes
275 Set Point Phase L3 dmd> (SP.
IL3 dmd>)
Set Points(MV) OUT on
off
* * LED BO 135 235 1 Yes
276 Set Point positive sequence
I1dmd> (SP. I1dmd>)
Set Points(MV) OUT on
off
* * LED BO 135 236 1 Yes
277 Set Point |Pdmd|> (SP. |Pdmd|>) Set Points(MV) OUT on
off
* * LED BO 135 237 1 Yes
278 Set Point |Qdmd|> (SP. |Qdmd|>) Set Points(MV) OUT on
off
* * LED BO 135 238 1 Yes
279 Set Point |Sdmd|> (SP. |Sdmd|>) Set Points(MV) OUT on
off
* * LED BO 135 239 1 Yes
285 Power factor alarm (cosϕ alarm) Set Points(MV) OUT on
off
* * LED BO 135 245 1 Yes
301 Power System fault
(Pow.Sys.Flt.)
P.System Data 2 OUT ON
OFF
ON * 135 231 2 Yes
302 Fault Event (Fault Event) P.System Data 2 OUT * ON * 135 232 2 No
303 E/Flt.det. in isol/comp.netw. (E/F
Det.)
P.System Data 2 OUT ON
OFF
* ON * 135 233 2 No
351 >Circuit breaker aux. contact:
Pole L1 (>CB Aux. L1)
P.System Data 2 SP * * * LED BI BO 150 1 1 Yes
352 >Circuit breaker aux. contact:
Pole L2 (>CB Aux. L2)
P.System Data 2 SP * * * LED BI BO 150 2 1 Yes
No. Description Function Type
of In-
for-
matio
n
Log Buffers Configurable in Matrix IEC 60870-5-103
Event Log ON/OFF
Trip (Fault) Log ON/OFF
Ground Fault Log ON/OFF
Marked in Oscill. Record
LED
Binary Inputs
Function Key
Relay
Chatter suppression
Type
Information Number
Data Unit
General Interrogation
To Next Page
Loading...
