Siemens SITRANS LUT400 Series - Page 592

A5E33329501 SITRANS LUT400 (HART) – INSTRUCTION MANUAL SITRANS LUT400 (HART) – INSTRUCTION MANUAL Page 279
Appendix C: menu chart
2.6.7 TABLE 1-8
2.6.8 TABLE 9-16
2.6.9 TABLE 17-24
2.6.10 TABLE 25-32
2.7 PUMPS
2.7.1 BASIC SETUP
2.7.1.1 PUMP CONTROL ENABLE
2.7.1.2 RELAY PUMP 1
2.7.1.3 RELAY PUMP 2
2.7.1.4 PUMP CONTROL MODE (LUT420)
2.7.1.5 PUMP CONTROL MODE (LUT430, 440)
2.7.1.6 ON SETPOINT PUMP 1
2.7.1.7 OFF SETPOINT PUMP 1
2.7.1.8 ON SETPOINT PUMP 2
2.7.1.9 OFF SETPOINT PUMP 2
2.7.1.10 SERVICE RATIO PUMP 1
2.7.1.11 SERVICE RATIO PUMP 2
2.7.2 MODIFIERS
2.7.2.1 WALL CLING REDUCTION
2.7.2.1.1 ENABLE
2.7.2.1.2 LEVEL SETPOINT VARIATION
2.7.2.2 ENERGY SAVINGS (LUT430, 440 only)
2.7.2.2.1 ENABLE
2.7.2.2.2 PEAK LEAD TIME
2.7.2.2.3 PEAK 1 START TIME
2.7.2.2.4 PEAK 1 END TIME
2.7.2.2.5 PEAK 2 START TIME
2.7.2.2.6 PEAK 2 END TIME
2.7.2.2.7 PEAK 3 START TIME
2.7.2.2.8 PEAK 3 END TIME
2.7.2.2.9 PEAK 4 START TIME
2.7.2.2.10 PEAK 4 END TIME
2.7.2.2.11 PEAK 5 START TIME
2.7.2.2.12 PEAK 5 END TIME
2.7.2.2.13 PEAK ON SETPOINT PUMP 1
2.7.2.2.14 PEAK OFF SETPOINT PUMP 1
2.7.2.2.15 PEAK ON SETPOINT PUMP 2
2.7.2.2.16 PEAK OFF SETPOINT PUMP 2
2.7.2.3 PUMP RUN-ON (LUT430, 440 only)
2.7.2.3.1 ENABLE
2.7.2.3.2 RUN-ON INTERVAL
2.7.2.3.3 RUN-ON DURATION PUMP 1
2.7.2.3.4 RUN-ON DURATION PUMP 2
2.7.2.4 PUMP START DELAYS (LUT430, 440 only)
2.7.2.4.1 DELAY BETWEEN STARTS
2.7.2.4.2 POWER RESUMPTION DELAY
2.7.3 TOTALIZERS (LUT430, 440 only)
2.7.3.1 RUNNING TOTALIZER
2.7.3.2 TOTALIZER DECIMAL POSITION
2.7.3.3 TOTALIZER MULTIPLIER
2.7.3.4 INFLOW/DISCHARGE ADJUST
2.7.3.5 RESET RUNNING TOTALIZER
2.8 ALARMS
2.8.1 HIGH LEVEL ALARM
2.8.1.1 ENABLE
2.8.1.2 HIGH LEVEL VALUE ON
2.8.1.3 HIGH LEVEL VALUE OFF
2.8.1.4 ASSIGNED RELAY
2.8.1.5 ALARM STATE
2.8.2 LOW LEVEL ALARM
2.8.2.1 ENABLE
2.8.2.2 LOW LEVEL VALUE ON
2.8.2.3 LOW LEVEL VALUE OFF
2.8.2.4 ASSIGNED RELAY
2.8.2.5 ALARM STATE
2.8.3 SWITCH (DI) ALARM
2.8.3.1 ENABLE
2.8.3.2 DISCRETE INPUT NUMBER
2.8.3.3 DISCRETE INPUT STATE
2.8.3.4 ASSIGNED RELAY
2.8.3.5 ALARM STATE
2.8.4 IN-BOUNDS LEVEL ALARM
2.8.4.1 ENABLE
2.8.4.2 HIGH LEVEL VALUE
2.8.4.3 LOW LEVEL VALUE
2.8.4.4 ASSIGNED RELAY
2.8.4.5 ALARM STATE
2.8.5 OUT-OF-BOUNDS LEVEL ALARM
2.8.5.1 ENABLE
2.8.5.2 HIGH LEVEL VALUE
2.8.5.3 LOW LEVEL VALUE
2.8.5.4 ASSIGNED RELAY
2.8.5.5 ALARM STATE
2.8.6 LOW TEMPERATURE ALARM
2.8.6.1 ENABLE
2.8.6.2 LOW TEMPERATURE VALUE ON
2.8.6.3 LOW TEMPERATURE VALUE OFF
2.8.6.4 ASSIGNED RELAY
2.8.6.5 ALARM STATE
2.8.7 HIGH TEMPERATURE ALARM
2.8.7.1 ENABLE
2.8.7.2 HIGH TEMPERATURE VALUE ON
2.8.7.3 HIGH TEMPERATURE VALUE OFF
2.8.7.4 ASSIGNED RELAY
2.8.7.5 ALARM STATE
2.8.8 FAIL-SAFE FAULT ALARM
2.8.8.1 ENABLE
2.8.8.2 ASSIGNED RELAY
2.8.8.3 ALARM STATE
2.8.9 HIGH FLOWRATE ALARM (LUT440 only)
2.8.9.1 ENABLE
2.8.9.2 HIGH FLOWRATE VALUE ON
2.8.9.3 HIGH FLOWRATE VALUE OFF
2.8.9.4 ASSIGNED RELAY
2.8.9.5 ALARM STATE
2. SETUP - VOLUME (cont’d)
2. SETUP - ALARMS (cont’d)