Spinner SM100 - Page 6

Technical product documentation
6
 SPINNER Werkzeugmaschinenfabrik GmbH
SM-2-12/02
III. List of figures
Figure 3-1: Transportation of the grinding machine .............................................................................................3-5
Figure 3-2: Installation instruction........................................................................................................................3-6
Figure 4-1: Operating elements ............................................................................................................................4-2
Figure 4-2: Device to suck off the dust.................................................................................................................4-4
Figure 5-1: Main connection.................................................................................................................................5-2
Figure 5-2: Sockets...............................................................................................................................................5-2
Figure 5-3: Coolant pump.....................................................................................................................................5-3
Figure 6-1: Maintenance instructions for the grinding spindle .............................................................................6-2
Figure 6-2: Lubricating the swivel holder.............................................................................................................6-2
Figure 6-3: Lubricating the dividing apparatus.....................................................................................................6-3
Figure 7-1: Quick change unit - lever “closed“.....................................................................................................7-2
Figure 7-2: Quick change unit - lever “open“.......................................................................................................7-2
Figure 7-3: Quick change unit - changing the grinding wheel ..............................................................................7-3
Figure 8-1: Assembly fittings................................................................................................................................8-2
Figure 8-2: Assembly............................................................................................................................................8-3
Figure 8-3: Grinding wheels.................................................................................................................................8-3
Figure 9-1: Operating elements ............................................................................................................................9-2
Figure 9-2: Handling.............................................................................................................................................9-3
Figure 10-1: Clamping lever and adjusting elements..........................................................................................10-2
Figure 10-2: Cross table......................................................................................................................................10-2
Figure 10-3: Cross table......................................................................................................................................10-3
Figure 10-4: Fine adjustment..............................................................................................................................10-3
Figure 10-5: Swivel movement...........................................................................................................................10-4
Figure 10-6: Adjustment scale............................................................................................................................10-4
Figure 10-7: Handling.........................................................................................................................................10-5
Figure 10-8: Adjusting the clearance angle ........................................................................................................10-5
Figure 11-1: Dividing apparatus.........................................................................................................................11-2
Figure 11-2: Shifting the dividing apparatus ......................................................................................................11-2
Figure 11-3: Adjusting the dividing scale...........................................................................................................11-3
Figure 11-4: Handling.........................................................................................................................................11-3
Figure 11-5: Indexing .........................................................................................................................................11-4
Figure 11-6: Grinding.........................................................................................................................................11-4
Figure 12-1: Clamping plate...............................................................................................................................12-2
Figure 12-2: Clamping bracket of the camping plate..........................................................................................12-2
Figure 12-3: Stopper...........................................................................................................................................12-3
Figure 13-1: Centering bracket...........................................................................................................................13-2
Figure 13-2: Contacting the tool.........................................................................................................................13-2
Figure 13-3: Contacting the tool.........................................................................................................................13-3
Figure 13-4: Adjusting the radius .......................................................................................................................13-3
Figure 13-5: Adjusting the radius .......................................................................................................................13-4
Figure 13-6: Adjusting the clearance angle ........................................................................................................13-5
Figure 13-7: Turning angle.................................................................................................................................13-5
Figure 13-8: Grinding the radius.........................................................................................................................13-6
Figure 13-9: Grinding the radius.........................................................................................................................13-6
Figure 13-10: Grinding the radius.......................................................................................................................13-7
Figure 13-11: Grinding the radius.......................................................................................................................13-7
Figure 14-1: Halving the cutter...........................................................................................................................14-2
Figure 14-2: Halving the cutter...........................................................................................................................14-2
Figure 14-3: Grinding the cutter .........................................................................................................................14-3
Figure 14-4: Setting the turning angle ................................................................................................................14-3
Figure 14-5: Adjusting the turning angle............................................................................................................14-4
Figure 14-6: Setting the clearance angle.............................................................................................................14-4
Figure 14-7: Grinding the cutter .........................................................................................................................14-5
Figure 14-8: Grinding the cutter .........................................................................................................................14-5
Figure 14-9: Handling.........................................................................................................................................14-6
Figure 14-10: Grinding the cutter relief..............................................................................................................14-6
Figure 14-11: Grinding the cutter relief..............................................................................................................14-7
Figure 14-12: Milling cutter ...............................................................................................................................14-7
Figure 15-1: Coolant unit....................................................................................................................................15-2
Figure 15-2: Coolant hose ..................................................................................................................................15-3