EasyManuals Logo

Stanley NB08PT-18 User Manual

Stanley NB08PT-18
626 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #35 background imageLoading...
Page #35 background image
9. NB08PT18 TROUBLESHOOTING GUIDE
WARNING: Read instruction manual for tool itself together to understand the troubleshooting of tool.
Faulty Causes Solutions Page
Power does not turn
ON
1. Battery is not fully attached. Remove battery and re-insert. Reset
tool to home.
Refer tool manual
2. Battery is not fully charged. Charge battery. Refer tool manual
3. Battery is malfunction. Replace battery. -
4. Trigger module malfunction. Contact a local service centre. -
Screen freezes at
Stanley Engineered
Fastening Logo
1. Data reading error. Remove battery and reinsert. Press
trigger to turn ON.
-
2. Smart screen malfunction. Contact a local service centre. -
3. Trigger module malfunction. Contact a local service centre. -
4. Setting data are broken. Restore to factory setting. 27
Tool do not function
when mandrel was
push
1. Screen is not home screen
(Counter screen).
Get screen to home scrren. Touch
“Back home” icon to be back home.
10
2. Screen malfunction, freezing or all
white.
Remove battery and reinsert. Press
trigger to turn ON. Or set the tool to
default. If not solve, contact a local
service centre.
27
3. Alarm message is shown with beep
sound.
Reset alarm refering to the related
pages.
Each
4. Setting data are broken. Restore to factory setting. 27
5. Radio communication error. Restore to factory setting. If not slove,
contact local service centre.
-
6. If tool is already operating Continue with fastening or enforced
spin o
26
Tool does not operate
when trigger switch is
pressed.
1. Screen is not home screen
(Counter screen).
Get screen to home scrren. Touch
“Back home” icon to be back home.
10
2. Screen malfunction, freezing or all
white.
Remove battery and reinsert. Press
trigger to turn ON. Or set the tool to
default. If not solve, contact a local
service centre.
27
3. Not in operating Get the tool to operate -
Insu cient or excessive
fastening stroke.
1. Inappropriate setting value of
fastening stroke or fastening load
Please use appropriate setting value
15, 16, 17
2. Malfunction of control part. Set up to factory default condition. If it
does not return,contact a local service
centre.
-
3. Setting  le is malfunction. Restore to factory setting. 27
4. Trigger module or screen module
malfunction.
Contact a local service centre.
-
Stroke and Force value
setting cannot change
1. Value setting cannot be selected Select the value setting method
correctly.
15
2. Wrong password Default password: 2000 15
Tool does not count
correctly (does not
count or counts even if
it does not set nut).
1. Fastening force is too low. Reset stroke and force.
For aluminum M3 at extremely low
force, it cannot count in some cases.
9
2. Battery is not fully charge. Check battery charge level and charge
battery if low.
26
3. Battery is malfunction. Replace battery -
4. Setting  les are malfunction. Restore to factory setting. -
5. Calibration abnormal Contact a local service centre. 31
Assumed fully charge
battery fasterned low
number of nuts.
1. Battery is not fully charge. Check the battery level and fully
charge the battery.
26
2. Battery is malfunction. If power consumtion is faster than
usual, replace battery.
-
35
ENGLISH

Table of Contents

Other manuals for Stanley NB08PT-18

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Stanley NB08PT-18 and is the answer not in the manual?

Stanley NB08PT-18 Specifications

General IconGeneral
BrandStanley
ModelNB08PT-18
CategoryPower Tool
LanguageEnglish

Related product manuals