EasyManua.ls Logo

TDK-Lambda GENESYS 10KW - Status Control Commands

TDK-Lambda GENESYS 10KW
74 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
83
-
530
-
000 Rev.
G
61
The power supply can accept values higher 5% than the table values, however it is not recommended to
program the power supply over the rated values.
Table 7
-
5: OVP programming range
Table 7
-
6: UVL prog
ramming range
Model
Rated Output Vol
t
age (V)
Minimum
(V)
Maximum
(V)
Model
Rated Output Voltage (V)
Minimum
(V)
Maximum
(V)
7.5
-
1000
0.75
8.25
7.5
-
1000
0
7.125
10
-
1000
1
11
10
-
1000
0
9.5
12.5
-
800
1.25
13.75
12.5
-
800
0
11.875
20
-
5
00
2
22
20
-
500
0
19
25
-
400
2.5
27.5
25
-
400
0
23.75
30
-
333
3
33
30
-
333
0
28.5
40
-
250
4
44
40
-
250
0
38
50
-
200
5
55
50
-
200
0
47.5
60
-
167
6
66
60
-
167
0
57
80
-
125
8
88
80
-
125
0
76
100
-
100
10
110
100
-
100
0
95
125
-
80
12.5
137.5
125
-
80
0
118.75
1
50
-
66
15
165
150
-
66
0
142.5
200
-
50
20
220
200
-
50
0
190
250
-
40
25
275
250
-
40
0
237.5
300
-
33
30
330
300
-
33
0
285
400
-
25
40
440
400
-
25
0
380
500
-
20
50
550
500
-
20
0
475
600
-
17
60
660
600
-
17
0
570
7.9.6
Status Control Commands
Refer to Section 7
-
10 f
or definition of the registers.
#
Command
Description
1
STT?
Reads the complete power supply status.
Returns ASCII characters representing the following data, separated by commas:
MV<actual (measured) voltage> PC<programmed (set) current>
PV<programmed (set) voltage> SR<status register, 2
-
digit hex>
MC<actual (measured) current> FR<fault register, 2
-
digit hex>
Example response: MV(45.201),PV(45), MC(4.3257), PC(10), SR(30), FR(00)
2
FLT?
Reads Fault Conditi
onal Register. Returns 2
-
digit hex.
3
FENA
Set Fault Enable Register using 2
-
digit hex.
4
FENA?
Reads Fault Enable Register. Returns 2
-
digit hex.
5
FEVE?
Reads Fault Event Register. Returns 2
-
digit hex. Clears bits of Fault Event Register.
6
STAT?
Read
s Status Conditional Register. Returns 2
-
digit hex.
7
SENA
Sets Status Enable Register using 2
-
digit hex.
8
SENA?
Reads Status Enable Register. Returns 2
-
digit hex.
9
SEVE?
Reads Status Event register. Returns 2
-
digit hex. Clears bits of Status Event re
gister.

Table of Contents

Related product manuals