Home
Thunder Laser
Engraver
Nova
Page 115
Thunder Laser Nova - Page 115
115 pages
Manual
Save Page as PDF
To Previous Page
To Previous Page
Loading...
www.thunderlaser.com
DONGGUAN
THUNDER LA
SER EQUIPMENT
CO.,LTD
tech@thunder
laser
.com
Shatian
Town,
Shatian
Dadao,
Mintian
Tel
:
(86)769
826653
Dongguan
City,
Guangdong
Province,
Ch
ina
1
14
2.
The set
ting f
or Int
egra
ted motor
, like
below
.
End.
114
Table of Contents
Main Page
Table of Contents
1
Chapter1 General Question
3
How to Disassemble Nova
3
Operation Manual for Thunder Laser Machine
5
System Maintenance
10
Daily Check List
10
Weekly Check List
11
Monthly Check List
12
How to Judge if the Laser Power Become Weaker
16
Chapter2 Laser Cutter Machine
17
Alarm of LCD Panel-Frame/X/Y Slop over
17
Alarm of LCD Panel-No Enough Extend Space
18
Alarm of LCD Panel-Water Error
20
Alarm of LCD Panel-Machine Protected
22
The Machine Won't Turn on
23
Y-Axis Not Moving at All
25
X-Axis Not Moving at All
27
The Laser Tube Won't Fire the Beam
29
Why the Red Dot Pointer Not Being Able to Come out from the Laser Head
31
Why the "Origin" Button of LCD Panel Not Working
33
Engraving Problem-The Engraving Quality Is very Poor
34
Cutting Problem- Why the Starting Point of a Cutting Graphic Can't Meet with Its
38
End Point
38
Why Noisy While Moving Laser Head Front and Back, How to Adjust
42
Why Does the Machine Beep Continuously
45
Chapter3 Laser Cutter Software
49
How to Prepare Your Files for Feeding into the Laser Program to Engrave
49
How to Prepare Your Files for Feeding into the Laser Program to Cut
55
Communication Error
57
Ethernet Cable Connection
57
USB Cable Connection
60
How to Run Several Laser Machines with One PC Via Ethernet Cable
62
How to Run Several Laser Machines with One PC Via USB Cable Connection
64
How to Setup Wireless Network Connection for Thunder Laser Machine
66
How to Run Several Laser Machines with One PC Via USB Cable
69
How to Import PDF Files into Rdworks
70
How to Install the Coreldraw Plugin for Rdworks
71
Wrong Proportions from Rdworks
73
Why Does the Graphic Size that Imported to Rdworks Different from Its Original Size
75
Engraving Problem-How to Improve Engraving Quality in the Scan Mode of X-Swing
76
Why Does the Cutting and Engraving Graphics Reverse (Mirror)
80
Laser Cutter Has a Wrong Cutting/Engraving Size
81
Laser Cutter's LCD Panel in Chinese
85
Chapter4 Component Maintenance
86
How Do I Replace the Controller Board
86
How to Replace Laser Tube
90
Disassembly Procedure
90
How to Adjust and Replace the Motor
92
How to Calibrate the Working Table to Level
94
How to Replace the Rollers and Adjust the X Axis Shaft
96
How to Adjust the Verticality between the X and y Axis
99
How Do I Replace the Drive Shaft Module
102
External Accessory Problem
106
Exhaust Fan Cannot Extract Smoke or Dust
106
Air Pump Won't Work or no Air Assist When Job Starts
107
Chiller Alarms Unusually
109
Rotary Axis Attachment Has a Wrong Cylindrical Engraving/Cutting Size
111
Related product manuals
Thunder Laser NOVA-24
77 pages
Thunder Laser NOVA- 35
77 pages
Thunder Laser NOVA-51
70 pages
Thunder Laser NOVA Series
77 pages
To Previous Page
