Page 10

VALCO MELTON MCP-8 - Page 10

120 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Section 1 Introduction MC095 - MCP-8 Control Unit

10

Table of Contents

Table of Contents5
Section 1 - Introduction9
System Description9
Features/Capabilities9
Section 2 - Safety and Use11
Read Thoroughly before Handling Equipment11
Symbols11
Owner Responsibilities12
Limitations of Use12
Installation/Startup/Use Safety Information13
Shut down Safety Information14
Hot-Melt-Specific, General Safety Information14
What to Do if Contact with Hot Adhesive Occurs15
What to Do if Inhalation of Adhesive Fumes Occurs15
What to Do if Adhesive-Related Fire or Explosion Occurs16
Hose Safety Information17
Section 3 - Basic Features19
MCP-8 Control19
Front Panel19
Unpacking19
Mounting the MCP-820
Standard Mounting System20
Standard System Mounting Footprint21
Swivel Mount (Used with 138Xx021)22
Swivel Mount Mounting Footprint22
Mounting the Encoder23
Installing the Glue Station24
MCP-8 Connections25
Pinouts, Standard26
Pinouts, Tri-Valve29
MCP-8 Valve Driver Instructions32
Wiring the Scanner Cable32
Section 4 - Programming35
Programming35
The Operator Interface Buttons35
The Status Leds35
Navigation and Edit Buttons36
Enter Password36
Password Levels37
Level 2 Password Options37
Protected Level Mode37
Main Menu Buttons38
Single Digit Vs. Thumbwheel Edit38
Valve Buttons39
Configuring the Valve/Channel Settings39
Valve Selection39
Valve Type40
Encoder Ratio41
Diagnostic Screen43
Compensation Time44
Parameter/Button Access Configuration46
Jam Detection49
Jam Detection Setup Menu50
Tipsealer51
Reversible Glue Station Setting55
Backup (Archive)56
Replace Micro-SD Card58
Reprogram/Reinitialize59
Section 5 - Operation61
Set the Pattern Menu Information61
Set the Pressures66
Purge and Test Run68
Job Screen69
Loading a Job69
Saving a Job70
Deleting a Job71
Copying a Job71
Archive Screen72
Service Screen73
Section 6 - Maintenance75
Purging the Adhesive75
Performing Downtime Maintenance75
Flushing the Glue System76
Lubricating the System76
Section 7 - Specifications77
Section 8 - Part Number List79
How to Order Parts79
Unit - Standard, Stand-Alone (074Xx071)80
Unit - Standard, Stand-Alone, for Tri-Valve Boardrunner (074Xx062)82
Unit - Standard, Remote (074Xx072)84
Unit - Remote Base Assembly, for Tri-Valve Boardrunner (074Xx063)86
Rack Assembly (074Xx070)88
Rack Assembly (074Xx058)90
Recommended Replacement Parts92
On PCB Assy., Power Control (151Xx719)92
On Main PCB Assy., Valves 1-4 (152Xx715)93
On PCB Assy., Valves 5-8 (152Xx721)94
On PCB Assy., Tri-Valve Manifold (151Xx674)94
Unit - Remote Display Touchscreen (138Xx021)95
Cover Assembly (026Xx385)97
Unit - Previous Version (074Xx060)99
Recommended Replacement Parts101
(On PCB Assembly, 151Xx697)101
On PCB Assembly,152Xx715101
Standard Mounting System101
Wiring Diagrams102
Flexoseal with MCP-8, Stand-Alone Standard [074Xx071]102
Flexoseal with MCP-8, Remote Standard [074Xx072]103
Flexoseal with MCP-8, Stand-Alone Tri-Valve Non-Contact [074Xx062]104
Flexoseal with MCP-8, Remote Tri-Valve Non-Contact [074Xx063]105
Section 9 - Warranty107
Warranty Information107
Cold Glue Equipment and Electronic Controls107
Hot Melt Units, Hoses, Valves, Guns, and Related Equipment107
Section 10 - Service109
Appendix A - Job Charts111
Appendix B - System Connectivity (Clearvision)113

EasyManua.ls – Your Ultimate Manuals Destination!

With a comprehensive collection of over 1 million PDF manuals, service guides, instruction booklets, and quick start guides, we cover every aspect of your needs. Explore manuals for products from more than 50,000 brands all in one place. Search and instantly view the manual you’re looking online for free.

Privacy Policy
Contact Us

© Copyright 2025 EasyManua.ls. All Rights Reserved.