Wintriss wpc 2000 User Manual

WPC 2000 User Manual 1128500
Table of Contents vii
Figure 2-12. WPC 2000 Main Processor Board (Right or Center Configuration): Location of
Important Components .................................................................................................2-23
Figure 2-13. WPC 2000 Main Processor Board (Left Configuration): Location of Important
Components ..................................................................................................................2-24
Figure 2-14. Overrun Sensor Magnet Placement: Dwell as a Function of Shaft Diameter ..............2-26
Figure 2-15. Overrun Sensor Magnetic Switch: Installation Example .............................................2-27
Figure 2-16. WPC 2000 Display Board: Location of Important Components .................................2-34
Figure 2-17. Cam Output Enclosure: Mounting Dimensions ...........................................................2-37
Figure 2-18. Cam Output Board: Mounting Dimensions .................................................................2-37
Figure 2-19. Connectors TB2 through TB5 on Cam Output Board .................................................2-39
Figure 2-20. Installing a Suppressor across an AC Load ..................................................................2-40
Figure 2-21. Installing a Diode across a DC Load ............................................................................2-40
Figure 2-22. “Set Cams” Switch (S701) Positions ...........................................................................2-41
Figure 2-23. One-hand Control Switch: Mounting Dimensions .......................................................2-44
Figure 2-24. One-hand Control Switch Base: Mounting Dimensions ..............................................2-45
Figure 2-25. Wiring Connections in One-hand Control Switch (Switch Cover, Bottom View) ......2-46
Figure 2-26. Bar Control Enclosure: Mounting Dimensions ............................................................2-47
Figure 2-27. WPC 2000 Mounting Plate: Mounting Dimensions ....................................................2-52
Figure 2-28. WPC 2000 Panel Mount Display: Mounting and Cutout Dimensions ........................2-53
Figure 2-29. Selector Switch: Cutout Dimensions ...........................................................................2-55
Figure 2-30. WPC 2000 Display Board Kit: Mounting and Cutout Dimensions .............................2-56
Figure 2-31. Reset/Select Button Wiring Connections .....................................................................2-57
Figure 3-1. WPC 2000 Display Showing Indicator Segments .........................................................3-2
Figure 3-2. WPC 2000 Display Showing “System Initialized” (“Int”) Message .............................3-3
Figure 3-3. WPC 2000 Display Showing “Resolver Zeroed” (“rES”) Message ..............................3-4
Figure 3-4. WPC 2000 Display Showing “Initializing Start-time Limit” (“Str”) Message ..............3-5
Figure 3-5. Setting Overrun Timing: Example .................................................................................3-9
Figure 3-6. WPC 2000 Display Showing Overrun Sensor “On” Angle .........................................3-10
Figure 3-7. WPC 2000 Display Showing Stop-time Limit Value ..................................................3-16
Figure 3-8. WPC 2000 Display Showing Results of 90° Stop-time Test .......................................3-17
Figure 3-9. Safety Distance: Distance between Pinch Point and Light Curtain .............................3-20
Figure 3-10. WPC 2000 Display Showing Micro-inch Time Setting ...............................................3-25
Figure 3-11. S101 Option Switch OFF and ON Settings ..................................................................3-26
Figure 3-12. Cam Channel Settings Display: Cam 1 ON Angle (270°) Shown ...............................3-34
Figure 3-13. Cam Channel Settings Display: Cam 1 OFF Setting (325°) Shown ............................3-35
Figure 3-14. WPC 2000 LED Indicator Map (Center- or Right-mounted Board) ............................3-37
Figure 3-15. WPC 2000 LED Indicator Map (Left-mounted Board) ...............................................3-38
Figure 3-16. WPC 2000 Display Board LED Indicator Map ...........................................................3-39
Figure 4-1. WPC 2000 Display with “Stopping Angle” Value Shown ............................................4-4
Figure 4-2. WPC 2000 Display with “Counter” Value Shown ........................................................4-5
Figure 4-3. WPC 2000 Display with “Counter Preset” Value Shown ..............................................4-7
Figure 5-1. WPC 2000 Display Showing Fault Code .......................................................................5-2
Figure 5-2. WPC 2000 Display Showing Lockout Message ............................................................5-3
Figure 5-3. WPC 2000 Display Showing Stopping Time Fault .......................................................5-4
Figure 5-4. Ross DM2 DSV Showing Reset Button .......................................................................5-22
Figure C-1. Option 1 Board Installed on WPC 2000 Main Processor Board ...................................C-4
Figure C-2. WPC 2000 Option 1 Board ...........................................................................................C-5
Figure C-3. WPC 2000 Option 1 Board: LED Map .........................................................................C-7

Wintriss wpc 2000 Specifications

General

Brand	Wintriss
Model	wpc 2000
Category	Controller
Language	English