5-15
IM 701310-17E
Commands
Command Function Page
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter?
Queries all settings related to the parameter of the history search condition. 5-105
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:CATegory
Sets the parameter category or queries the current setting. 5-105
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>?
Queries all settings related to the FFT search. 5-105
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
CALCulation<x>
Sets the upper and lower limits of the calculation item of the FFT search or
queries the current setting.
5-105
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
PEAK?
Queries all settings related to the peak value of the FFT search. 5-105
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
PEAK:DFREquency
Sets the upper and lower limits between the peak frequencies of the FFT
search or queries the current setting.
5-106
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
PEAK:DV
Sets the upper and lower limits between the peak voltages of the FFT search
or queries the current setting.
5-106
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
PEAK:FREquency<x>
Sets the upper and lower limits of the peak frequency of the FFT search or
queries the current setting.
5-106
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:FFT<x>:
PEAK:V<x>
Sets the upper and lower limits of the peak voltage of the FFT search or
queries the current setting.
5-106
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:MEASure?
Queries all settings related to the search using automated measurement of
waveform parameters (measure search).
5-106
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:MEASure:
CALCulation<x>
Sets the upper and lower limits of the calculation item of the measure search
or queries the current setting.
5-107
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:MEASure:
TRACe<x>?
Queries all settings related to the trace of the measure search. 5-107
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:MEASure:
TRACe<x>:AREA<x>?
Queries all settings related to the area of the measure search. 5-107
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:MEASure:
TRACe<x>:AREA<x>:TYPE?
Queries all settings related to the waveform parameters of the measure
search.
5-107
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:
MEASure:TRACe<x>:AREA<x>:
TYPE:<Parameter>
Sets the upper and lower limits of the waveform parameter of the measure
search or queries the current setting.
5-108
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:XY<x>?
Queries all settings related to the XY search. 5-108
:HISTory[:CURRent][:SEARch]:
SELect<x>:PARameter:XY<x>:
XYINteg
Sets the upper and lower limits integral value of the XY search or queries the
current setting.
5-108
:HISTory[:CURRent][:SEARch]:
SELect<x>:RECTangle?
Queries all settings related to the rectangle search. 5-108
:HISTory[:CURRent][:SEARch]:
SELect<x>:RECTangle:HORizontal
Sets the horizontal position of the rectangle used in the rectangle search or
queries the current setting.
5-108
:HISTory[:CURRent][:SEARch]:
SELect<x>:RECTangle:VERTical
Sets the vertical position of the rectangle used in the rectangle search or
queries the current setting.
5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:TRACe
Sets the source trace of the history search or queries the current setting. 5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:WAVE?
Queries all settings related to the search in the waveform zone (wave
search).
5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:WAVE:EDIT<x>:EXIT
Exits the zone edit menu of the wave search. 5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:WAVE:EDIT<x>:PART
Sets the editing of the portion of the zone of the wave search. 5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:WAVE:EDIT<x>:WHOLe
Sets the editing of the entire zone of the wave search. 5-109
:HISTory[:CURRent][:SEARch]:
SELect<x>:WAVE:TRANge
Sets the range over which to perform the wave search or queries the current
setting.
5-110
5.1 List of Commands
To Next Page
Loading...
Need help?
General
