2gig Technologies EDGE - Arming in Away Mode and Notes

68 pages

To Next Page

To Previous Page

Installation Guide for the 2GIG EDGE Security Panel

4. Insert the new battery, and attach the power cable

Connect

Power

5. Replace the back cover.

Replacing the Battery (continued)

Main Page

Table of Contents2
Introduction5
About this Guide5
Document Conventions5
Safety Precautions and Notations5
Technical Support5
Taking Security Innovation to the 2GIG EDGE Security Panel6
Capabilities of the 2GIG EDGE Panel6
Introduction to Smart Areas7
Internal Components8
Additional Accessories9
Kits & Keypads9
Antennas9
Sensors & Peripherals9
Smart Home Controls9
Important Information10
For Residential Settings10
Operating Temperature10
Planning the Installation10
Choose the Location for the Panel's Backplate10
Recommended Tools and Equipment10
Choose the Wall Location10
Where to Place Wireless Sensors11
Where to Place Burglary Protection Sensors12
Where to Place Fire Protection Sensors12
Where NOT to Install a Smoke Alarm12
Install External Attic Mount Antenna (Optional)13
Mount Antenna13
Install Jumper14
Connect the Antenna15
Mount the Panel16
Mount the Backplate to a Wall16
Connect an External Alarm Sounder17
To Connect an External Alarm Sounder to the 2GIG EDGE Panel17
Optional Desktop Kit17
Connect the Hardwire Loops18
To Install the Hardwire Loop Wiring for the Contact Sensors18
Connect the Power Wires19
Terminal Block - Maximum Wire Gauge and Length19
Connecting the Power Supply to the 2GIG EDGE Panel19
Connect Power (Barrel Connector)20
Connect the Backup Battery20
Warning20
Replacing the Battery21
Terminal Blocks Wiring Diagram23
Control Panel Wiring Diagram24
Hang the 2GIG EDGE Panel25
Install Retaining Wall Bracket and Connect the AC Power Supply25
Update Firmware26
Installer Toolbox27
Panel Programming - Wireless Zones28
Panel Programming - Built-In Zones30
Panel Programming - Keyfobs33
Panel Programming - Keypads35
Panel Programming - Image Sensors37
Panel Programming - Network Settings39
Forget Network40
Join Other Network40
Wps40
Smart Home Settings41
System Test42
Panel Programming - Advanced Programming43
Advanced Programming43
System Configuration43
Q101: Change Installer Code43
Q102: Security Pin Code Length43
Q103: Lock Installer Programming44
Q104: Lock Default Programming44
Q105: 2-Way Voice44
Q106: Disable Siren after Two-Way Audio44
Q107: Smart Areas44
Q108: Z-Wave Feature45
Q109: Master User Can Access Z-Wave Setup45
Q110: Smart Home Controls Require Master Code45
Q111: Main Panel Sounder Follows45
Q112: Z-Wave Siren Mode45
Q113: Quick Arming45
Q114: Auto Stay45
Q115: Exit Delay Restart46
Q116: Allow Quick Exit46
Q117: Quick Bypass46
Q118: Auto Unbypass for Manual Bypass46
Q119: Alert on Disarm with Keyfob after Alarm46
Q120: Keyfob Arm/Disarm Confirmation47
Q121: Keyfob/Remote Arming Mode on System Not Ready47
Q122: Alarm Cancel Display47
Q123: Cross Sensor Zones 99-10047
Q124: Event Logs47
Q125: LED Mode Control47
Q126: Commercial Burglary Support47
Timers, Delays & Counts48
Q201: Exit Delay, in Seconds48
Q202: Entry Delay 1, in Seconds48
Q203: Entry Delay 2, in Seconds48
Q204: Alarm Cancel Time, in Minutes48
Q205: Alarm Abort Window Transmission Delay48
Q206: Burglary Bell Cutoff Time48
Q207: Fire Bell Cutoff Time49
Q208: Swinger Shutdown Count49
Q209: Cross Sensor Timeout, in Seconds49
Q210: Time to Detect AC Loss, in Minutes49
Q211: Random AC Loss Report Time49
Q212: Siren Supervision Time50
Panel Configurations50
Q301: Police Emergency Key50
Q302: Fire Emergency Key50
Q303: Emergency Key50
Q304: On-Board Camera50
Q305: Temperature Display Units51
Q306: Configuration Change Acknowledgement51
Q307: Open Collector #1 Output51
Q308: Open Collector #2 Output51
Q309: Allow Backlight Always on51
Troubles52
Q401: Radio Modem Network Failure Time, in Minutes52
Q402: Radio Network Failure Causes Trouble52
Q403: Radio Network Failure Reports52
Q404: Broadband Network Failure Time in Minutes52
Q405: Broadband Network Failure Causes Trouble52
Q406: Broadband Network Failure Reports52
Q407: Trouble Doesn't Sound at Night53
Q408: RF Jam Causes Trouble53
Q409: System Tamper Causes Trouble53
CS Reporting53
Q501: CS Lack of Usage Notification Time, in Days53
Q502: Periodic Test, in Days53
Q503: Programming Mode Entry Reports to CS53
Q504: Trouble Reports to CS54
Q505: Trouble Restore Reports to CS54
Q506: Manual Bypass Reports to CS54
Q507: Bypass Restore Reports to CS54
Q508: Force Bypass Reports54
Q509: AC Loss Reports to CS54
Q510: AC Restore Reports to CS54
Q511: System Low Battery Reports to CS55
Q512: System Low Battery Restore Reports to CS55
Q513: RF Low Battery Reports to CS55
Q514: Sensor Low Battery Restore Reports to CS55
Q515: System Disarmed Reports to CS55
Q516: System Armed Reports to CS55
Q517: Alarm Restore Reports to CS55
Q518: Smart Test Reports56
Restore the Factory Default Settings56
2Gig Edge Remote Keypad56
Panel Programming57
Sensor Programming Reference57
Sensor Equipment Type58
Equipment Codes58
Transmission ID (TXID)59
Normal State59
Sensor Loop59
Transmission Delay60
Voice Descriptor60
Sensor Reports61
Sensor Supervised61
Sensor Chime61
Advanced Programming Reference62
ANSI/SIA CP-01-2010 Features to Limit False Alarms66
Limited Warranty67
Waste Electrical and Electronic Equipment (WEEE) Statement67
Warnings67
Limitations of Alarm Products67
Risk of Noise Induced Hearing Loss67

2gig Technologies EDGE - Arming in Away Mode and Notes

Table of Contents

Other manuals for 2gig Technologies EDGE

Related product manuals