Agilent Technologies 5975 Series

To Next Page

To Previous Page

4 Operating in EI Mode

5975/5977 Series MSD Operating Manual 99

Enable the GC/MS Interface and Oven

Procedure

1 Click Method > Instrument Setup > GC > Aux Heaters.

2 Select On for Thermal Aux 2.

3 Click Oven and select On.

4 Click Download Method to enable these temperature zones in the GC.

5 Save the method.

Main Page

Hardware User Information4
- 5977B Msd4
- 5975/5977 Series MSD Prior to the 5977B MSD4
- Table of Contents5
Introduction9
5977B Series MSD Version10
Abbreviations Used11
The 5977B Series MSD13
MSD Hardware Description15
Important Safety Warnings16
Hydrogen Safety19
- GC Precautions19
- Precautions21
Safety and Regulatory Certifications23
Intended Use26
Cleaning/Recycling the Product26
Accidental Liquid Spillage26
Moving or Storing the MSD26
To Replace the Primary Fuses27
Installing 7890/7820/6890/6850 GC Columns29
Columns30
To Install a Capillary Column in a Split/Splitless Inlet32
To Condition a Capillary Column35
To Install a Capillary Column in the GC/MS Interface Using the Self-Tightening Column Nut36
To Install a Capillary Column in the GC/MS Interface Using a Standard Column Nut41
- Nut41
To Install the Interface Tip Seal44
To Calibrate Column Flow Linear Velocity46
The GC/MSD Interface for a 7890B Series GC49
Intuvo 9000 GC Column Maintenance51
Columns52
- Conditioning Columns53
- Tips and Hints53
- Handling the Intuvo 9000GC Column and Bus Components54
To Replace an Intuvo GC Column55
To Replace an Intuvo 9000 GC Gasket59
To Install a Column Guard or Jumper Chip60
To Replace the 9000 GC/MS Tail64
To Condition an Intuvo Capillary Column68
To Install the Interface Tip Seal70
The GC/MS Interface for a 9000 Series GC72
Operating in EI Mode75
Operating the MSD from the DS76
Operating the MSD from the GC Control Panel77
Configuring the MSD through the Web User Interface (WUI)81
- To Change the Network Settings of the MSD81
Operating the 5975/5977 MSD from the Local Control Panel (LCP)84
- Modes of Operation84
- LCP Status Messages86
- To View System Status During Startup87
Emodule Mini Display Readout91
Front Panel Instrument Status LED91
The GC/MSD Interface92
Before You Turn on the MSD94
Pumping down95
Controlling Temperatures95
Controlling Column Flow95
Venting the MSD96
Set MS Analyzer Temperatures97
Enable the GC/MS Interface and Oven99
View MSD Temperatures and Vacuum100
To Run an Autotune102
To Open the MSD Covers103
Vent the MSD104
To Pump down the MS106
To Move or Store the MSD109
General Maintenance111
Before Starting112
Maintaining the Vacuum System116
Maintaining the Analyzer117
To Open the Analyzer Chamber119
To Remove the EI HES121
To Connect/Disconnect Wiring to the EI HES123
To Disassemble the EI HES124
To Clean the EI HES127
To Assemble the EI HES130
To Remove the EI HES Filaments135
To Install the EI HES Filament137
To Install the EI HES138
To Remove the EI XTR, SS, or Inert Source139
To Connect/Disconnect Wiring from the EI XTR, SS, and Inert Sources140
To Disassemble the EI SS or EI Inert Source141
To Disassemble the EI XTR Source144
To Clean an EI XTR, SS, or Inert Source147
To Assemble an EI SS or Inert Source151
To Assemble the EI XTR Source154
To Replace a Filament in an EI XTR, SS, or Inert Source157
To Install the EI XTR, SS, or Inert Source159
To Replace the Electron Multiplier Horn160
To Close the Analyzer Chamber162

Table of Contents

Other manuals for Agilent Technologies 5975 Series

Related product manuals