Agilent Technologies 8922M - Page 378

Index
Index-8
Pseudo-Random Bit Sequence, 4-42
Pulse
RF Generator, 4-117
pulse demodulation test
RF analyzer, 3-12
pulse measurement, 2-16
pulse modulation
RF generator, 4-117
pulse modulation test, 3-8
Pulse On/Off Fall
Pulse, 4-105
pulse on/off ratio, 4-104
Pulse On/Off Rise
Pulse, 4-105
Pwr Ramp
Summary, 4-101
R
RACHs
call counts, 4-43
Cell Control, 4-43
radio frequency analyzer, 4-112
radio frequency generator, 4-115
radio specifications, 8-33
radio tests
reduce testing time, 8-33
selecting, 8-32
ramping
output RF spectrum power, 4-83
Range Hold
Configure, 4-51
Rcv Pace, 8-6
Configure, 4-62
read-only setting
on the memory card, 8-22
read-write setting
on the memory card, 8-22
recall
keys, 5-7
receive call
keys, 5-7
receive pacing
setting, 4-62
Receive/Transmit Pacing, 8-6
record size
for data collection, 8-35
Ref Level
Spectrum Analyzer (Main Controls), 4-
123
Ref Level (Marker To)
Spectrum Analyzer (Marker Controls),
4-126
Reference
Configure, 4-52
reference
setting, 5-8
reference level
RF Input, 4-123
reference output
option 001, 4-51
reference set
keys, 5-8
Relative MS Timing Err
Cell Control, 4-43
release
keys, 5-8
Remote control, A-12
ResAllFS, 4-10, 4-14
Reset
Cell Control, 4-43
Oscilloscope (Trigger Controls), 4-79
reset
call count, 4-43
cell control, 4-29
measurement, 4-51, 4-76, 4-78
SACCH Meas, 4-43
ResTypeI, 4-10, 4-14
ResTypeIa, 4-10, 4-14
ResTypeIB, 4-10, 4-14
ResTypeII, 4-10, 4-14
RF analyzer, 4-112
RF analyzer screen
keys, 5-9
RF Anl Ampl Control
Cell Control, 4-44
RF Cnt Gate
CW Meas, 4-55
RF generator, 4-115
amplitude, 4-8, 4-12, 4-17, 4-23, 4-37
RF generator screen
keys, 5-9
RF In/Out
Configure, 4-52
RF Input
CW Meas, 4-55
RF Analyzer, 4-114
Spectrum Analyzer (Auxiliary Con-
trols), 4-128
RF Level Offset
Configure, 4-53
RF Output
RF Generator, 4-117
RF ovrload message, 7-4
RF spectrum measurement, 2-20
RFGen Volts
Configure, 4-52
Rise Pos
Pulse, 4-105
RJ-11/RS-232 adapter, 8-5
RMS Error
Phase/Freq (Multi-burst), 4-89
RMS Phase Error
Phase/Freq (Main), 4-87
RS-232 printer, 8-31
RS-232 Serial port, 8-5
Run Mode
Continuous or Single Step, 8-30
Run Test, 8-15
Run/Stop
Control, 4-10
Meas Cntl, 4-14
S
SACCH Meas
Cell Control, 4-45
save
keys, 5-9
Save Programs On Memory Cards, 8-10
scope
cell control, 4-29
Scope In
Audio, 4-4, 4-75, 4-77, 4-80
Scope Lvl
Oscilloscope (Trigger Controls), 4-79
Screen Freeze
Configure, 4-53
screens, 4-1
active cell+, 4-31