Astoria Core 600 - Manual Introduction and Storage

TECHNICIANS' manual 7 of 104
1. INTRODUCTION
Read this manual carefully. It provides important safety infor-
mation to the Technician regarding the operations indicated
in this document.
Keep this Manual in a safe place. If you lose it, you can ask the
Manufacturer for another copy.
The Manufacturer of the appliance cannot be held responsi-
ble for any damage caused due to the non-observance of the
requirements listed in this manual.
Before carrying out operations on the machine, read
the instructions contained in this publication and fol-
low the guidelines carefully. Keep this manual and all
attached publications in an accessible and secure place.
This document assumes that the machine is installed in a lo-
cation where the current work safety and hygiene standards
are observed.
The instructions, drawings and documentation contained in
thisManualaretechnicalandcondential.Theyarethesole
property of the Manufacturer, and may not be fully or par-
tially reproduced in any way.
The Manufacturer reserves the right to make any improve-
ments and/or modications to the product. We guarantee
thatthisManualreectsthetechnicalstateoftheappliance
at the time it was released to the market.
We encourage the Technicians to make any proposals in re-
gards to improving the product or its Manual.
1.1 Guidelines for reading the Manual
This Manual is divided into separate chapters. The chapter
order is linked to the temporal logic of the life of the machine.
Terms, abbreviations and pictograms are used to facilitate
the immediate understanding of the text.
This Manual consists of cover, index and series of chapters.
Each chapter is sequentially numbered. The page number is
shown in the footer.
Themachineidenticationdataisdisplayedonthemachine’s
nameplate and the EU declaration of Conformity, whilst the
date and revision of the Instruction Manual is provided on
the last page.
Abbreviations
Sec. = Section
Chap. = Chapter
Para. = Paragraph
P. = Page
Fig. = Figure
Tab. = Table
Units of measurement
The units of measurement are those provided by the Interna-
tional System (SI).
1.2 Storing the Manual
The Instruction Manual must be stored carefully. The manual
should be stored, handled with care with clean hands and not
placed on dirty surfaces. The Manual must be stored in an
environment protected from moisture and heat.
Do not remove, tear or arbitrarily modify any of its parts.
On the Technician's request, the manufacturer can provide
additional copies of the machine's Instruction Manual.
1.3 Method for updating the Instruction
Manual
The Manufacturer reserves the right to modify and make im-
provements to the machine without providing notice or up-
dating the Manual that has already been received.
Should the Manual become illegible or otherwise
hard to read, the Technicians must request a new
copy from the Manufacturer before carrying out
any operations on the machine.
It is absolutely forbidden to remove or rewrite parts of the
Manual.
The instructions, drawings and documentation contained
in this manual are condential and the sole property of the
Manufacturer. They may not be reproduced in any way, ei-
ther in full, or in part without prior authorisation.
The Technician is responsible for complying with the instruc-
tions contained in this Manual.
Should any incident occur as a result of these recommenda-
tions being used incorrectly, the Manufacturer declines any
liability.
This manual is also available on the manufacturer’s website
(indicated on the cover of the manual).
1.4 Recipients
This Manual is intended for the Technician who is responsible
for carrying out the following operations on the machine:
• Transport and handling;
• Storage;
• Installation;
• Commissioning;
• Maintenance;
• Cleaning;
• Spare part replacement;
• Emergency operations and faults;
• Decommissioning;
• Disassembly;
• Disposal (refer to the retailer if not directly responsible).
RECIPIENT QUALIFICATIONS
The machine is intended for a professional non-generalised
use, therefore the Technician must:
• Have attended the training courses organised by the Man-
ufacturer relating to the type of machine;