100
AVR21ENR1 Remote Control
There are two options in LEARN CODE.
Learn Device: This option allows adding a single IR command
to the AVR21ENR1
Input Select Buttons 3, for functions such
as PLAY for a DVD/CD, VR, etc. It can also be used to output any
command that may be desirable when selecting a particular source
such as issuing a screen aspect ratio command, or other video
display command.
Learn Button: This option allows adding a single IR command to
any button on the AVR21ENR1. This is useful when a particular
code is not included in the onboard IR code library or for adding
a special function for another device when a particular source has
been selected.
NOTE: The Learn Button can only be used for learn-
ing IR commands for TV and Game/CAM. TV and Game/CAM are
the only two settings that output a devices original IR codes directly.
For all other devices (common sources), the AVR21ENR1 outputs
proprietary commands that are interpreted by the AVR and
converted to the original codes. To add IR commands to buttons
for these other devices, use the OSD Menu Learning as described
in the
Remote Control Setup/Learn Codes section.
To teach commands from one product’s remote into the
AVR remote, follow the steps below:
The process requires that both the device’s original remote and the
AVR remote be available. Before pressing any buttons on either
remote, place them so that the IR transmitter on the remote
belonging to the device to be programmed is facing the
Infrared
Lens
on the AVR remote. The two remotes should be no more
than an inch apart and there should not be any direct sunlight or
other bright light source near the remotes.
Learn Device
1. Press and hold the Rem Menu Button for about three
seconds while the message HOLD BUTTON FOR S SECONDS
appears in the remote’s LCD
Information Display 2. Release
the button when the red light under the
Set Button H appears.
2. The remote’s MAIN MENU message will appear in the LCD and
the
Set Button H will remain illuminated in red. Press the
⁄
Navigation Button F once so that LEARN CODE appears on
the bottom line of the LCD screen, as shown in
Figure 94.
Figure 94.
3. Press the Set Button H. The message in the LCD will change
to the LEARN CODE menu (
Figure 95). The bottom line will
default to the LEARN DEVICE option.
Figure 95.
Figure 92.
9. If the device being programmed does turn off after following
the instructions in Step 7, you will need to verify the code set by
pressing the
Alphanumeric Keys in sequence, as instructed
in
Figure 93. Point the remote at the device being programmed,
and press the
“1” Button to see whether the device
turns back on.
Figure 93.
10. After pressing and releasing the “1” Button , check to see
whether the device has turned back on. If it has, skip to Step 12.
If it does not turn off, press the
“2” Button , or the next
button in the numeric sequence if you are repeating the
procedure, as instructed by the LCD screen in
Figure 93.
11. When pressing the “1” button does not turn the device being
programmed back on, repeat the procedure by trying the
remainder of the
Alphanumeric Keys in sequence, each
time pressing and then releasing the button to see whether the
new device turns back on. When it does, skip to the next step.
However, if you try all 10 numeric keys and find that the unit
will not turn on, you won’t be able to use this method to pro-
gram the device. Press the
Rem Menu Button to exit the
programming process. You’ll need to follow the Learning
Commands instructions below to enter the codes for this
device into the AVR remote.
12. When pressing one of the numeric keys in Step 10 or 11 causes
the device being programmed to turn back on, follow the
instructions shown in
Figure 93 and press the Set Button H
within 5 seconds of the device turning on. After you press the
Set Button H, the top line of the LCD will read SAVING…
and then the word SAVED will flash four times in the center
of the bottom line.
13. When the codes are saved, the remote will return to normal
operation, and whenever you press the TV or Game/Cam but-
ton that was just programmed, the codes for the new device
will be used.
Learning Commands
On occasions when the AVR remote does not contain the codes for
a particular product’s remote in its built in library, or when you
wish to program a missing or special function into one button of a
device, the AVR remote’s learning capability allows you to do that.
To Next Page
Loading...