Manual Program
Selecting this mode will allow you to manually select the type of
device (DVD, Sat, etc.), brand (Sony, Toshiba, etc.) and code group
for a specific device. This method is more direct and will be a
little faster than the automatic mode, which will search the
entire library for codes.
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the
MANUAL line. Press the
Set Button H. The DISC 1
MANUAL PROG
screen will appear (
Figure 54). Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed at SOURCE
TYPE
.
Figure 54.
IR Manual Program Screen
Press the
‹
/
›
Navigation Button F to select the source type:
DVD or CD. Press the
⁄
/
¤
Navigation Button F to move the
cursor next to BRAND. Press the
‹
/
›
Navigation Button F to
select the appropriate brand.
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
TRY CODES. With the AVR21ENR1 Main Room remote pointing
toward the AVR front panel, slowly press the
Alphanumeric
Buttons
, through the range indicated on screen, until the unit
being configured turns off. When the unit turns off, press the
⁄
/
¤
Navigation Button F to move the cursor next to YES. This will
“save” this code group for control of the source selected.
Press the
Exit Button G to exit the Menu. Press the appropriate
Input Selector 3 on the AVR21ENR1 remote to select the source
and then press various control buttons (Play, Stop, Track, numeric
functions, etc.) to confirm IR codes. If some commands are missing
(not included in the library), they can be added individually by
using the LEARN CODE option in CONTROL SETUP. If only a
few IR codes need to be added to the setup as configured using
the internal IR code library, proceed to LEARN CODE. If no code
group was found within a specific brand for a specific device,
follow the instructions in AUTOMATIC PROGRAM.
If the appropriate code group has been configured, return to the
REMOTE CONTROL SETUP 1 screen to configure the next
source’s IR codes. Repeat until all sources are set up for IR control.
Automatic Program
The Automatic Program option will check all codes available for
a specific type of device (DVD, Sat, etc.) in the onboard IR Code
Library to try to match a set of commands with a particular device.
To open the AUTOMATIC CODE PROGRAM screen, press the
Menu Button to bring the MAIN MENU to the screen. Press
the
⁄
/
¤
Navigation Button F so that the cursor is pointed at
the REMOTE CONTROL SETUP line. Press the
Set Button H.
The REMOTE CNTL SETUP 1 screen will appear. Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed at the
source to be configured (for example, Disc 1 will be used). Press the
Set Button H. The DISC 1 CONTROL SETUP screen will
appear. Press the
⁄
/
¤
Navigation Button F so that the cursor is
pointed at the PROGRAM CODE line. Press the
Set Button H.
The DISC 1 CODE PROGRAM screen will appear. Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed at the
AUTOMATIC line. Press the
Set Button H. The DISC 1
AUTO PROGRAM screen will appear (
Figure 55).
Figure 55.
Source Auto Program Screen
With the cursor pointed at the SOURCE line, press the
‹
/
›
Navigation Button F to select the type of source. (The setup will
confine the options to source types relevant to the selected input
(Disc 1 = DVD; CD; VR = VCR; TIVO; DVDR, etc.). Press the
Set
Button H
to select the source type. Press
¤
to move the cursor
next to TRY CODES. Repeatedly press the
‹
or
›
Navigation
Button F
to test all selected device type commands until the unit
turns off. When the unit turns off, press the
¤
Navigation Button
F
to move the cursor next to YES. Press the Set Button H to
“save” the code group.
Press the
Exit Button G to exit the menu. Press the appropriate
Input Selector 3 on the AVR21ENR1 remote to select the source
and then press various control buttons (Play, Stop, Track, numeric
functions, etc.) to confirm IR codes. If some commands are missing
(not included in the library) or if no proper code group was found,
they can be added individually by using the LEARN CODE option
in CONTROL SETUP.
If the appropriate code group has been configured, return to the
REMOTE CONTROL SETUP 1 screen to configure the next
source’s IR codes. Repeat until all sources are set up for IR control.
Learn Code
If specific commands are missing from Program Setup (not included
in the library), if no proper code group was found or if a special
command is required, they can be added individually by using the
LEARN CODE option in CONTROL SETUP.
To open the LEARN CODE screen, press the
Menu Button
on the remote to bring the MAIN MENU to the screen. Press the
To Next Page
Loading...