To configure IR commands for HT Master:
Press the Menu Button on the remote to bring the MAIN
MENU to the screen. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at the REMOTE CONTROL SETUP line.
Press the
Set Button H. The REMOTE CNTL SETUP 1
screen will appear. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at GO TO REMOTE CNTL 2. Press the
Set Button H. The REMOTE CNTL SETUP 2 screen will
appear (
Figure 57).
Figure 57.
Remote Control Setup 2 Screen
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the ASSIGN TRIGGER OUT line. Press the
‹
/
›
Navigation
Button F
to select the device to be controlled with a constant
12V DC control voltage.
TRIGGER would typically be used with a TV or projector that can
be turned ON/OFF with a 12V DC signal or a motorized screen that
will drop when a 12V signal is present and retract when the con-
trol voltage is removed. Another possible option is a control volt-
age to a lighting system that can take a constant 12V DC control
signal and convert it to a “movie mode” lighting scene and then
restore normal room lighting when the voltage is removed.
NOTE: This function can only be assigned to ONE device. Once
TRIGGER has been assigned to TV/Projector, Screen or Lighting,
the Trigger setup option will only appear on the setup page for
that device. See
Voltage Control at the end of the TV/Projector,
Screen
and Lighting sections for configuration.
TV/Projector On/Off
To turn the TV/Projector ON/OFF with the AVR, in the REMOTE
CNTL SETUP 2 screen, press the
⁄
/
¤
Navigation Button F
so that the cursor is pointed to the TV/PROJECTOR ON/OFF
line. Press the
Set Button H. The TV/PROJ CONTROL
SETUP screen will appear.
Carrier
With the cursor positioned next to CARRIER, press the
‹
/
›
Navigation Button F to select the proper setting. NOTE: Most IR
remotes used with common-source components will have a carrier,
so YES should be selected as a first test. Some cable box remotes
do not use a carrier, so if a code setting doesn’t work, try changing
this setting.
Invert Code
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
INVERT CODE. Press the
‹
/
›
Navigation Button F to select
YES/NO. Most devices will be set to NO. Certain devices (Sony
S-Link remote control In) will require a YES setting. Try changing
this setting if a specific code selection does not work for a given
device.
Program Code
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
to the PROGRAM CODE line. Press the
Set Button H. The
TV/PROJ CODE PROGRAM screen will appear.
TV/Proj Program Code (Manual)
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the MANUAL line. Press the
Set Button H. The TV/PROJ
MANUAL PROG screen will appear. SOURCE TYPE will be fixed
as selected (TV/PROJ).
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to BRAND. Press the
‹
/
›
Navigation Button F to select the
appropriate brand.
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
TRY CODES. With the AVR21ENR1 Main Room Remote pointing
toward the AVR’s front panel, starting with 1, slowly press the
numeric buttons through the range indicated on screen, until the
unit being configured turns off. When the unit turns off, press the
⁄
/
¤
Navigation Button F to move the cursor next to YES.
Press the
Set Button H. This will “save” this code group for
ON/OFF control of the TV/projector.
If no IR ON/OFF commands were found, see
Automatic and Learn,
below.
If no further programming is required, press the
AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to return
to normal operation mode.
To continue in setup, press the
¤
Navigation Button F to move
the cursor next to BACK TO T/P CODE PROG. Press the
Set Button H. Press the
¤
Navigation Button F again to
move the cursor next to BACK TO T/P CNTL SETUP.
Press the
Set Button H. The TV/PROJ CONTROL SETUP
screen will appear.
To program SCREEN UP/DOWN, LIGHTING ON/OFF,
CURTAIN OPEN/CLOSE, press the
⁄
/
¤
Navigation Button
F
to move the cursor next to BACK TO REM CNTL SETUP.
Press the
Set Button H. See the Screen Control and Lighting
Control
sections.
TV/Proj Program Code (Automatic)
If ON/OFF codes could not be found by Brand in the Manual Mode,
try searching by source type in the Automatic mode.
In the TV/PROJ CODE PROGRAM screen, press the
⁄
/
¤
Navigation Button F to move the cursor next to AUTOMATIC.
Press the
Set Button H. The TV/PROJ AUTO PROGRAM
screen will appear.
The SOURCE will be fixed as selected (TV/PROJ). Press the
¤
Navigation Button F to move the cursor next to TRY CODES.
Repeatedly press the
‹
or
›
Navigation Button F to test all
71
System Setup
To Next Page
Loading...