4. Input Selectors: Pressing one of these buttons will turn on
the local zone, if it is off. (If the AVR21EN is off, the press
of an input selector will turn the AVR on to Multi-Zone
On.) If the local zone is on, these buttons will select the
common sources, as connected to the AVR source inputs,
and switch the remote to control of that device.
5.
TV Mode Select: Press this button to switch the remote
keys to control the local TV or video display.
6.
Local 2 Select: Press this button to control a local source.
7.
Disc Direct: Press this button when a disc changer is in
use, to directly enter a disc number. After pressing this
button, press the appropriate
Alphanumeric Keys to
select a disc.
8.
Disc Memory Button: Press this button once to select the
beginning (point A) and again to select the end point
(point B) of a passage you wish to play repeatedly. Press
the button again to end repeat playback. A-B repeat play
is not available for VCD, MP3, WMA or JPEG discs.
9.
Direct/List Select Button: Press this button when the
tuner is in use, to directly enter a station’s frequency; or
when a CD is in use, to directly enter a track number. After
pressing this button, press the appropriate
Alphanumeric
Keys
to select a station or track. This button also
activates the List function for TiVo
®
players. See your TiVo
owner’s manual for more information on the List function.
10.
Clear Button: Press this button to cancel button presses
of
Alphanumeric Keys after pressing the Direct/List
Select Button
. The remote will return to normal
control mode.
11.
Angle/Tuning Mode Button: When the DVD mode is
active, press this button to select an alternate camera
angle, if available on the current DVD.
12.
Guide/Level Button: Press this button to open the
Channel Guide when controlling a cable box or satellite
receiver.
13.
Navigation Disc: This single disc-like button is used to
navigate the on-screen configuration menus, to scroll
through option lists and to select various settings such
as delay, speaker configurations, surround modes, digital
inputs, etc. To use the button, simply press it up, down,
left or right, in the direction indicated by the
⁄
/
¤
‹
/
›
icons printed on the disc.
14.
Exit/Cancel Button: When programming the remote,
press this button to exit Setup. When controlling a cable
box or satellite receiver, press this button to turn off an
on-screen Guide or Menu.
15.
Set Button: Press this button for Enter or OK, with most
menu driven devices.
111
NOTES:
I The function names shown here are each button’s function
when used with a KP21 keypad and AVR21EN controller (sys-
tem). Most buttons have additional functions when used with
other devices, and some of these functions may be assigned to
different buttons, depending on which device was selected.
The device name will appear in the upper line of the LCD
Information Display and the function assigned to that
device will appear in the lower line when the button is pressed.
See the KP21R Function List (
Figure 154) for a list of the func-
tions assigned to each button for each device type.
I Some buttons have special functions when they are pressed
and held for 3 seconds.
I The jack on the upper right side of the remote is reserved for
future use. Do not remove the plug provided or connect any
device to the jack.
I The KP21R remote control may be programmed to control up to
10 devices. Before using the remote, it is important to press the
Input Selector that corresponds to the device you wish to
operate.
I The remote is capable of operating a wide variety of products,
as configured in the
AVR21EN REMOTE CONTROL SETUP.
The KP21R sends proprietary Audioaccess codes that are inter-
preted by the AVR21EN and output as the original manufacturer’s
codes through the respective
Control Out IR outputs on the
AVR rear panel.
I Only the TV, Local 1 and Local 2 devices are controlled directly
with the KP21R. Those codes are programmed in the remote.
See the
Programming the KP21R Remote Control/Learning
Commands
section.
1.
Power Off (All): Press this button to turn the local zone
OFF. If the Multiroom system is active in other zones,
including the Main Room, the AVR21EN will continue to
function. If the local zone is the last active zone in the
system, the AVR will turn off all common-source
components and switch itself to Standby.
2.
Power On (All): Press this button to turn on the local zone.
If any other zone is active, the local zone will turn on to
either the source selected when the zone was turned off
or the source designated in POWER ON MODE. If no other
zones are active, the AVR21EN will turn on and display
MULTI-ZONE ON, but it will not turn on the Main Room
or any other zones. The AVR will turn all common-source
components on.
3.
LCD Information Display: This two-line screen displays
remote menus and various source/function information,
depending on the commands that have been entered into
the remote.
KP21R Remote Control Features
To Next Page
Loading...