94
AVR21ENR1 Remote Features
4. Input Selectors: Pressing one of these buttons will perform
three actions at the same time. First, if the AVR21EN is not
turned on, this will power up the unit. Next, it will select the
source shown on the button as the input to the AVR21EN.
Finally, it will change the remote control so that it controls the
device selected. After pressing one of these buttons, you may
need to press the
AVR Button (System Selector) 4 again
to operate some AVR21EN functions with the remote.
5.
System Selector (AVR Button): Pressing this button will switch
the remote so that it will operate the AVR21EN's functions
(accessing menus, etc.). If the AVR21EN is in the Standby mode,
it will also turn the AVR21EN on.
6.
TV Mode Select: Press this button to switch the remote keys
to directly control the local TV or video display.
7.
6CH/8CH Input Select: Press this button to select the device
connected to the
8-Channel Direct Inputs 6. See the Main
Room Installation and Setup/8 Channel DVD Audio
section
for more information.
8.
Faroudja
®
Processor On/Off: Press this button to activate the
DCDi
®
by Faroudja processor. Press again to deactivate the
processor.
FAROUDJA ON/OFF will appear in the AVR’s
Upper Display Line .
9.
Test Tone Button: Press this button to stop the sequence used
to calibrate the AVR21EN’s output levels during EzSet/EQ. See
the
AVR21EN Configuration/EzSet/EQ and Output Level
Adjustment
sections for more information on calibrating the
AVR21EN speaker level audio output.
10.
Disc Direct (Unmarked Round Blue Button): Press this
button when a disc changer is in use, to directly enter a disc
number. After pressing this button, press the appropriate
Alphanumeric Keys to select a disc.
11.
Audio Input Selector: After pressing the AVR button, press
this button to select one of the
Digital Audio Inputs IN for
use with its source, or to select the analog audio input for that
source using the
⁄
/
¤
Navigation Button F. It is possible to
reassign a digital audio input to sources with selectable audio
inputs, even if the audio is from a different source than the one
selected for play. See
AVR21EN Configuration/Source Audio
Input
for more information on using digital inputs.
12.
Direct/List Select Button: Press this button when the tuner is
in use, to directly enter a station’s frequency, or when a CD is in
use to directly enter a track number. After pressing this button,
press the appropriate
Alphanumeric Keys to select a station
or track. This button also activates the List function for TiVo
players. See your TiVo
®
Owner’s Manual for more information
on the List function.
13.
Surround Mode Select Button: After pressing the AVR button,
press this button to select one of the DSP audio surround
modes, such as Dolby,
®
Logic 7
®
or DTS NEO:6
®
or DSP. Each
press of the button selects another mode. Pressing the
⁄
/
¤
Navigation Button F after one of the modes has been selected
allows a choice of various options within the different surround
modes. See the
AVR21EN Configuration/Audio Mode and
Main Room Operation/Surround Mode Selection sections
for descriptions of the different surround modes and options.
AVR21ENR1 Feature Descriptions
NOTES:
I The function names shown here are each button’s function
when used with the AVR21EN. Most buttons have additional
functions when used with other devices, and some of these
functions may be assigned to different buttons, depending on
which device was selected. The device name will appear in the
upper line of the LCD
Information Display 2 and the function
assigned to that device will appear in the lower line when the
button is pressed. See the
AVR21ENR1 Function List section
for a list of the functions assigned to each button for each
device type.
I Some buttons have special functions when they are pressed and
held for 3 seconds.
I The jack on the upper right side of the remote is reserved for
future use. Do not remove the plug provided or connect any
device to the jack.
I The AVR21ENR1 remote control may be programmed to control
up to 11 devices. Before using the remote, it is important to
press the
Input Selector 3 that corresponds to the device you
wish to operate.
I The remote is capable of operating a wide variety of products
made by other manufacturers, using control codes that are
programmed into the remote’s code library. As described in
AVR21EN Configuration/Remote Control Setup and
Programming the KP21ENR1 Remote Control, it is simple to
program the remote to operate your device by selecting the
device type and brand, and then programming the correct set
of codes for that brand.
IMPORTANT NOTE: With the exceptions of the AVR, TV and
Game/Cam, the codes output by the AVR21ENR1 are proprietary
Audioaccess IR codes that are received by the AVR21EN and con-
verted to the actual IR codes for the sources being controlled.
These IR codes are output via emitters connected to the IR
Control Outputs on the AVR21EN rear panel.
1.
Power Off (All): Press this button to place the AVR21EN in the
Standby mode. Note that this will turn off the Main Room func-
tions, but if the Multiroom system is activated, the AVR will con-
tinue to function and the message
MULTI-ZONE ON will
appear in the
Lower Display Line on the AVR front panel.
2.
Power On (All): Press this button to turn the AVR on. When
properly set up, all common-source components will automatically
turn on as well. Press this button to turn on the power to TV or
Game/Cam after first pressing either the
TV 5 or Game/Cam
Button 3
.
3.
LCD Information Display: This two-line screen displays setup
menus and other information, depending on the commands
that have been entered into the remote.
To Next Page
Loading...