117
Learning Commands
On occasions when the KP21R remote control does not contain
the codes for a particular product’s remote in its built-in library, or
when you wish to program a missing or special function into one
button of a device, the KP21R remote’s learning capability allows
you to do that.
There are two options in Learn Code.
LEARN DEVICE: This option allows adding a single IR command
to the KP21R Input Select buttons, for functions such as Play for
a DVD/CD, video recorder, etc. It can also be used to output any
command that may be desirable when selecting a particular source,
such as issuing a screen aspect-ratio command, a video display
command, etc.
LEARN BUTTON: This option allows adding a single IR command
to any button on the KP21R. This is useful when a particular code
is not included in the onboard IR code library or for adding a spe-
cial function for another device when a particular source has been
selected, such as a light scene command when controlling Disc 1.
To teach commands from one product’s remote into the KP21R
remote, follow the steps below:
The process requires that both the device’s original remote and the
KP21R remote be available. Before pressing any buttons on either
remote, place them so that the IR transmitter on the remote from
the device to be programmed is facing the
Infrared Lens on
the KP21R remote. The two remotes should be no more than an
inch apart and there should not be any direct sunlight or other
bright light source near the remotes.
Learn Device
1. Press and hold the Rem Menu Button for about 3 seconds
while the message HOLD BUTTON FOR 3 SECONDS appears
in the remote’s LCD
Information Display . Release the button
when the red light under the
Set Button turns on.
2. The remote’s MAIN MENU message will appear in the LCD
and the
Set Button will remain illuminated in red. Press the
⁄
Navigation Button once so that LEARN CODE appears
on the bottom line of the LCD screen, as shown in
Figure 132.
Figure 132.
3. Press the Set Button . The message in the LCD will change
to the LEARN CODE menu (
Figure 133). The bottom line will
default to the LEARN DEVICE option.
Figure 133.
KP21R Remote Control Features
Press the Set Button . The message PRESS DEVICE TO
BE PROGRAMMED will appear in the LCD. Press the remote
Input Select Button to which the IR command is to be
added. The message PRESS BUTTON ON ORIGINAL
REMOTE will appear in the LCD.
With the two remotes properly positioned, lens to lens, press
the button on the original remote and hold it until CODE
LEARNED CONTINUE appears in the LCD. The
Set Button
will light red. Press the Set Button to “save” the com-
mand. The red light will turn off. The message PRESS DEVICE
TO BE PROGRAMMED will again appear in the LCD display.
Either press another
Input Select Button to teach addi-
tional commands to other input select buttons or press the
Rem Menu Button to exit LEARN Menu and return to
normal operation.
4. Press the
Input Select Buttons just programmed to
confirm proper system performance. If a code wasn’t learned
or if the wrong code was inadvertently programmed, repeat
the previous steps to make corrections.
Learn Button:
1. Press and hold the Rem Menu Button for about 3seconds
while the message HOLD BUTTON FOR 3 SECONDS appears
in the remote’s LCD
Information Display . Release the button
when the red light under the
Set Button turns on.
2. The remote’s MAIN MENU message will appear in the LCD
display and the
Set Button will remain illuminated in red.
Press the
⁄
Navigation Button once so that LEARN CODE
appears on the bottom line of the LCD screen, as shown in
Figure 134.
Figure 134.
3. Press the Set Button . The message in the LCD display will
change to the LEARN CODE menu (
Figure 135). The bottom
line will default to the LEARN DEVICE option.
Figure 135.
4. Press the
⁄
/
¤
Navigation Button to change the option in
the lower line to LEARN BUTTON. Press the
Set Button .
LOCAL 1 will default to the lower line, as shown in
Figure 136.
Figure 136.
To Next Page
Loading...