are only to be selected and controlled by the Main Room. If a
source has been blocked (NO), a message will appear on the
KP21 Information Display: SOURCE NOT AVAILABLE CHECK
SETTINGS.
Figure 60.
Assign Entertainment Services Screen
The system default permits all sources the remote zones, so if you
do not wish to block any sources from the remote zones, you may
skip this section and proceed to NAME PAGING GROUPS or
press the
Exit Button G to exit Setup. To assign Entertainment
Services by source:
1. From ZONE SETUP PAGE 1, with the cursor next to
ASSIGN ENTERTAINMENT SERVICES, press the
Set
Button H
. The ASSIGN ENTERTAINMENT SERVICES
screen will appear (
Figure 60).
2. Press the
⁄
/
¤
Navigation Button F to position the cursor next
to a source that is to be blocked from the remote zones.
3. Press the
‹
/
›
Navigation Button F to change that source’s
status to NO. The selected source will not be available to the
remote zones.
4. Repeat Steps 2–3 for any other sources to be blocked from the
remote zones.
5. To continue Setup, position the cursor next to BACK TO
ZONE SETUP and press the
Set Button H. The ZONE
SETUP PAGE 1 screen will appear.
6. To exit Setup and return to the system mode, press the
Exit Button G.
Name Paging Groups
Paging Groups are combinations of different zones that can be
selected at different times for Paging. Some typical examples
would be paging groups consisting of all bedrooms, just the
children’s bedrooms or a group including the living room, family
room and dining room. As part of the system default, there is an
ALL Group to page all zones, and each keypad can be selected
individually to page a particular zone. This leaves only the special
groupings required by the homeowner to be set up. It is recom-
mended that you discuss this option with the homeowner to
determine how best to configure this feature.
Figure 61.
Name Paging Groups Screen
This section names the paging groups. Building the groups will be
done in a later section. To name Paging Groups:
1. From ZONE SETUP PAGE 1, with the cursor next to
NAME PAGING GROUPS, press the
Set Button H. The
NAME PAGING GROUPS screen will appear (
Figure 61).
2. Press the
⁄
/
¤
Navigation Button F to position the cursor next
to NAME. Press the
Set Button H. A white rectangle will flash
to the right of NAME: indicating that the remote can be used
to enter the letters for the group name.
3. Using either the
⁄
/
¤
Navigation Button F or the
Alphanumeric Buttons , enter the first letter for the group
name (e.g., Bedrooms). When the first letter appears on screen,
press the
›
Navigation Button F to move the cursor to the
next letter position.
4. Repeat Steps 2–3 above until the Paging Group Name has been
spelled out. Press the
Set Button H. This will store the name
and the cursor will appear next to NAME.
5. To name additional groups, press the
⁄
/
¤
Navigation Button
F
to position the cursor next to GROUP. Press the
‹
/
›
Navigation Button F to select another group.
6. Repeat Steps 2–4 until all desired Paging Groups have been
named.
7. To exit Setup, press the
Exit Button G. To continue Zone Setup,
position the cursor next to BACK TO ZONE SETUP and press
the
Set Button H. ZONE SETUP PAGE 1 will appear.
Name Entertainment Groups
Entertainment Groups allow multiple zones to be turned on and
off together, using the Party Mode control. This feature is desirable
for parties, to be able to easily select background music through
common areas. The zones within the groups will turn on, and play
the same source. The zones within the groups can be configured
to each turn on to the same source, different sources or the last
source selected in each zone. Each zone within the group will
turn on to its preset volume or last volume set, as configured by
zone. The individual zones will maintain local volume and mute
functions. A zone can only be part of one Entertainment Group,
and multiple groups can be active at the same time.
To Next Page
Loading...