settings and displays, follow these steps:
1.Press and hold the
Rem Menu Button for about 3 seconds
while the message: HOLD BUTTON FOR 3 SECONDS appears
in the remote’s LCD
Information Display . Release the button
when the red light under the
Set Button appears.
2.The remote’s MAIN MENU message will appear in the LCD
and the
Set Button will remain illuminated in red. Press the
⁄
/
¤
Navigation Button until USER RESET appears on the
bottom line of the LCD screen, as shown in
Figure 149.
Figure 149.
3. Press the Set Button to reset the remote. Note that once
the
Set Button is pressed, the process may not be stopped.
While the remote’s memory is being cleared, a RESETTING...
message will appear in the upper line of the remote’s LCD screen,
as shown in
Figure 150. It may take a few minutes for the reset
process to be completed, and the length of time will vary, depending
on how much customization and programming has taken place.
Please be patient; as long as the message appears in the display,
the remote is functioning properly.
Figure 150.
4. When the remote has been totally reset and returned to the
factory default condition, a REMOTE RESET COMPLETE
message will appear (
Figure 151) briefly, and then the remote
will return to normal operation.
Figure 151.
Additional Notes on Configuring and Operating the Remote:
I When the remote is being programmed, it will automatically
time-out if no button is pressed within a 30 second period.
The message shown in
Figure 152 will appear briefly and
the remote will then exit the feature being programmed
and any data entered will be lost.
Figure 152.
I The programming or configuration process may also be
stopped at any time by pressing the
Rem Menu Button .
The message shown in
Figure 152 will appear, the data
entered in the current process will be lost and the remote will
return to normal operation. Any process that was underway
Read a Macro
To check the commands stored in the remote’s memory for one of
the buttons, follow these steps:
1. Press and hold the
REM MENU Button for about 3 seconds
while the message HOLD BUTTON FOR 3 SECONDS appears
in the remote’s LCD
Information Display . Release the but-
ton when the red light under the
Set Button appears.
2. The remote’s MAIN MENU message will appear in the LCD and
the
Set Button will remain illuminated in red. Press the
⁄
Navigation Button twice so that MACRO appears on the
bottom line of the LCD screen. Press the
Set Button to
enter the main macro menu branch.
3. At the next menu screen (
Figure 147), press the
⁄
/
¤
Navigation Button until the bottom line in the remote’s
LCD shows READ A MACRO. Press the
Set Button to
begin the process of reading a macro.
Figure 147.
4. The next display screen (Figure 148) is where you select the
macro to be read. Press the
⁄
/
¤
Navigation Button until the
name of the macro you wish to read appears. For this example,
we will read back Macro 1, created in a previous section. When the
name of the macro to be read appears, press the
Set Button .
Figure 148.
5. As soon as the Set Button is pressed, the first two steps in
the macro will be appear in the remote’s LCD screen. You may
then use the
⁄
/
¤
Navigation Button to step up or down
through the list of commands stored as the macro. As you read
the display, you will see
Input Selector Buttons appear
in brackets (e.g., [DISC 1]). When the step in the macro is a
function, navigation or any other button, it will appear next to
the bracketed read-out of the underlying device (e.g., [DISC 1]
POWER ON).
6. When you are finished reviewing the macro’s contents, press the
Set Button to return the remote to normal operation.
Resetting the Remote
Depending on the way in which the remote has been programmed,
there may be a situation in which you wish to totally erase all the
changes that have been made to the remote and return it to the
factory defaults. You may do that by following the steps shown
below, but remember that once the remote is reset, ALL changes
that have been made (including programming for use with other
devices, learned keys and macros) will be erased and any settings
you had previously made will have to be reentered. To erase all
settings and reset the remote to the original factory default
To Next Page
Loading...