the cursor is pointed at GO TO REMOTE CNTL 2. Press the
Set Button H. The REMOTE CNTL SETUP 2 screen will
appear. Press the
⁄
/
¤
Navigation Button F so that the cursor is
pointed at the LIGHTING CONTROL line. Press the
Set Button
H
. The LIGHTING CONTROL SETUP screen will appear.
Carrier
With the cursor positioned next to CARRIER, press the
‹
/
›
Navigation Button F to select the proper setting. NOTE: Most IR
remotes used with common-source components will have a carrier,
so YES should be selected as a first test. Some cable box remotes
do not use a carrier, so if a code setting doesn’t work, try changing
this setting.
Invert Code
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
INVERT CODE. Press the
‹
/
›
Navigation Button F to select
YES/NO. Most devices will be set to NO. Certain devices (Sony
S-Link, Harman Kardon remote control In) will require a YES
setting. Try changing this setting if a specific code selection does
not work for a given device.
Program Code
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the PROGRAM CODE line. Press the
Set Button H. The
LIGHTING CODE PROGRAM screen will appear.
Lighting Program Code (Manual)
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the MANUAL line. Press the
Set Button H. The LIGHTING
MANUAL PROG screen will appear. SOURCE TYPE will be fixed
as selected (LIGHTING).
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to BRAND. Press the
‹
/
›
Navigation Button F to select the
appropriate brand.
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
TRY CODES. With the AVR21ENR1 Main Room remote pointing
at the AVR’s front panel, starting with 1, slowly press the numeric
buttons through the range indicated on screen, until the unit
being configured turns off. When the unit turns off, press the
⁄
/
¤
Navigation Button F to move the cursor next to YES.
Press the
Set Button H. This will “save” this code group for
On/Off control of the lights.
If no IR On/Off commands were found, see
Lighting Program
Code (Automatic)
and Lighting Program (Learn Code).
If no further programming is required, press the AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to
return to normal operational mode.
To continue in setup, press the
¤
Navigation Button F to
move the cursor next to BACK TO LGT CODE PROG. Press
the
Set Button H. Press the
¤
Navigation Button F again
to move the cursor next to BACK TO LGT CNTL SETUP.
Press the
Set Button H. The LIGHTING CONTROL SETUP
screen will appear.
To program TV/PROJECTOR ON/OFF and SCREEN ON/OFF,
press the
⁄
/
¤
Navigation Button F to move the cursor next
to BACK TO REM CNTL SETUP. Press the
Set Button H.
See the
TV/Projector and Screen sections.
NOTE: If the AVR turns on to Multiroom mode, the Trigger Out
Jack
will stay at 0V DC until the Main Room is turned on.
Manual Via Remote: In this mode, the Trigger Out Jack
is controlled with the Trigger Button on the AVR21ENR1
remote. When the AVR is turned on, the Trigger Out has an
output of 0V DC. When the
Trigger Button on the remote is
pressed, the Trigger Out goes to +12V DC – in this case, to drop a
screen. Press the
Trigger Button again; the voltage is cut
and the screen retracts.
To configure the AVR21EN
Trigger Out Jack to drop a
projection screen when the Main Room is turned on:
Press the
Menu Button on the remote to bring the MAIN
MENU to the screen. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at the REMOTE CONTROL SETUP line.
Press the
Set Button H. The REMOTE CNTL SETUP 1 screen
will appear. Press the
⁄
/
¤
Navigation Button F so that the
cursor is pointed to GO TO REMOTE CNTL 2. Press the
Set
Button H
. The REMOTE CNTL SETUP 2 screen will appear.
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the ASSIGN TRIGGER OUT line. Press the
‹
/
›
Navigation
Button F
until SCRN appears. Press the
⁄
/
¤
Navigation
Button F
so that the cursor is pointed at SCREEN CONTROL.
Press the
Set Button H. Press the
⁄
/
¤
Navigation Button F
so that the cursor is pointed at the CONTROL line. Press the
‹
/
›
Navigation Button F to select the preferred mode. Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed at the
BACK TO REM CNTL SETUP line. Press the
Set Button H.
To test the Screen Up/Down commands with AVR On/Off, turn the
AVR off and manually raise the screen. To test the On function,
either press the
Standby/On Button 1 on the AVR’s front panel
or press the
On Button 1 on the AVR21ENR1 remote. The AVR
should turn on and the screen should drop.
To test the Off function, either press the
Standby/On Button 1
on the AVR’s front panel or press the Off Button 0 on the
AVR21ENR1 remote. The AVR should turn off and the screen
should retract.
To test the Screen Up/Down commands with Manual Via Remote,
turn the AVR off and manually raise the screen. Turn the AVR on
by pressing the
Standby/ON Button 1 on the AVR’s front panel
or press the
On Button 1 on the remote. (The AVR should be on,
but the screen should still be retracted.) Press the
Trigger Button
on the remote. The screen should drop. Press the Trigger
Button
again and the screen should retract.
Exit Setup
If no further programming is required, press the AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to return
to normal operational mode.
Lighting Control
To control the Main Room lighting with the AVR turn-on/turn-off
functions, press the
Menu Button on the remote to bring the
MAIN MENU to the screen. Press the
⁄
/
¤
Navigation Button F
so that the cursor is pointed at the REMOTE CONTROL SETUP
line. Press the
Set Button H. The REMOTE CNTL SETUP 1
screen will appear. Press the
⁄
/
¤
Navigation Button F so that
74
System Setup
To Next Page
Loading...