Figure 59.
Assign Services Screen
1. From ZONE SETUP PAGE 1, with the cursor next to
ASSIGN SERVICES press the
Set Button H. The ASSIGN
SERVICES screen will appear (
Figure 59).
2. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to ENTERTAINMENT. Using the
‹
/
›
Navigation Button F,
select YES to be able to select and control the common A/V
sources or NO if this function is not required.
3. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to PAGING. Using the
‹
/
›
Navigation Button F, select YES
to be able to talk to other zones using the KP21 built-in micro-
phone or NO if this function is not required.
4. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to MONITORING. Using the
‹
/
›
Navigation Button F, select
YES to be able to listen to other zones using the KP21 built-in
microphones and/or view activity in those zones if equipped
with cameras, or NO if this function is not required.
5. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to WAKE-UP. Using the
‹
/
›
Navigation Button F, select YES
to be able to configure individual zones or groups of zones to
turn on at specific times and to specific sources, or NO if this
function is not required.
6. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to SLEEP. Using the
‹
/
›
Navigation Button F, select YES
to be able to configure individual zones or groups of zones to
turn off at specific preprogrammed times or NO if this function
is not required.
7. Using the
⁄
/
¤
Navigation Button F, position the cursor next
to
DOOR SETUP and press the
Set Button H. Available
doors will be identified by
DOOR1: YES, DOOR2: YES, etc.
Using the
⁄
/
¤
Navigation Button F, place the cursor next to
DOOR NUMBER CAM and then using the
‹
/
›
Navigation
Button
F
select the camera to be assigned to that door.
8. When finished, either press the
Exit Button G on the remote
to return to system function or position the cursor next to
BACK TO ZONE SETUP and press the
Set Button H
to continue Zone Setup.
Assign Entertainment Services
This menu determines which common sources the remote zones
will have access to. Typically, all sources would be allowed (
YES),
but there may be some sources (such as a specific DVD player) that
To test the Curtain Open/Close commands with Manual Via
Remote, turn the AVR off and manually close the curtain. Turn the
AVR on by pressing the
Standby/On Button 1 on the AVR’s front
panel or press the
On Button 1 on the remote. (The AVR should
be on, but the curtain should still be closed.) Press the
Trigger
Button
on the remote. The curtain should open. Press the
Trigger Button again and the curtain should close.
Exit Setup
If no further programming is required, press the AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to return
to normal operational mode.
Zone Setup
With all system components installed and connected, the system
will function to its default settings. That is, a KP21 can turn the
system on, select and control sources and adjust volume,
in addition to some other basic functions.
There are other, more advanced system functions that require
setup, using the same on-screen menu that was used to set up
the Main Room, given that the use and configuration of every
system is different. To enter the Zone Setup mode:
1. In the Main Room, turn on the AVR21EN and main room video
display.
2. Press the
AVR Button 4 on the AVR21ENR1 Main Room remote.
3. Press the
MENU Button on the remote. The MAIN MENU
will appear (
Figure 58).
Figure 58.
Main Menu
4. Press the
¤
Navigation Button F until the cursor is next to
ZONE SETUP.
5. Press the
Set Button H. The ZONE SETUP PAGE 1 screen
will appear.
Assign Services
This menu will configure the multiroom section of the system for
various system functions such as Entertainment (A/V Sources),
Paging, Monitoring, Wake-Up Timers, Sleep Timers and Door
Answer. Any services turned off in this screen will not be available
to any part of the multiroom system. Setting the services by zone
is done in a later section. To assign system services: