Invert Code
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to INVERT CODE. Press the
‹
/
›
Navigation Button F to
select YES/NO. Most devices will be set to NO. Certain devices
(Sony S-Link, Harman Kardon remote control In) will require a
YES setting. Try changing this setting if a specific code selection
does not work for a given device.
Program Code
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the PROGRAM CODE line. Press the
Set Button H. The
CURTAIN CODE PROGRAM screen will appear.
Screen Program Code (Manual)
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the MANUAL line. Press the
Set Button H. The CURTAIN
MANUAL PROG screen will appear. SOURCE TYPE will be
fixed as selected (CURTAIN).
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to BRAND. Press the
‹
/
›
Navigation Button F to select the
appropriate brand.
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
TRY CODES. With the AVR21ENR1 Main Room remote pointing
at the AVR’s front panel, starting with 1, slowly press the numeric
buttons through the range indicated on screen, until the unit
being configured turns off. When the unit turns off, press the
⁄
/
¤
Navigation Button F to move the cursor next to YES. Press the
Set Button H. This will “save” this code group for On/Off control
of the curtain.
If no IR On/Off commands were found, see see
Lighting Program
Code (Automatic)
and Lighting Program (Learn Code).
If no further programming is required, press the AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to
return to normal operational mode.
To continue in setup, press the
¤
Navigation Button F to move
the cursor next to BACK TO CURTAIN CODE PROG. Press
the
Set Button H. Press the
¤
Navigation Button F again to
move the cursor next to BACK TO CURTAIN CNTL SETUP.
Press the
Set Button H. The CURTAIN CONTROL SETUP
screen will appear.
To program TV/PROJECTOR ON/OFF, DRAPES OPEN/CLOSE
and LIGHTING ON/OFF, press the
⁄
/
¤
Navigation Button F
to move the cursor next to: BACK TO REM CNTL SETUP.
Press the
Set Button H. See the TV/Projector, Drapes and
Lighting sections.
Curtain Program Code (Automatic)
If On/Off codes could not be found by Brand in the Manual mode,
try searching by source type in the Automatic mode.
At the CURTAIN CODE PROGRAM screen, press the
⁄
/
¤
Navigation Button F to move the cursor next to AUTOMATIC.
Press the
Set Button H. The CURTAIN AUTO PROGRAM
screen will appear.
The SOURCE will be fixed as selected (CURTAIN). Press the
¤
Navigation Button F to move the cursor next to TRY CODES.
Repeatedly press the
‹
or
›
Navigation Button F to test all
selected device type commands until the unit turns off. When the
screen will appear. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at GO TO REMOTE CNTL 2. Press the
Set Button H. The REMOTE CNTL SETUP 2 screen will appear.
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the ASSIGN TRIGGER OUT line. Press the
‹
/
›
Navigation
Button F
until LIGHT appears. Press the
⁄
/
¤
Navigation
Button F
so that the cursor is pointed at LIGHTING CONTROL.
Press the
Set Button H. Press the
⁄
/
¤
Navigation Button F
so that the cursor is pointed at the CONTROL line. Press the
‹
/
›
Navigation Button F to select the preferred mode. Press
⁄
/
¤
Navigation Button F so that the cursor is pointed at the BACK
TO REM CNTL SETUP line. Press the
Set Button H.
To test the Lighting On/Off commands with AVR On/Off, turn the
AVR off and manually turn the lights off. To test On, either press
the
Standby/On Button 1 on the AVR’s front panel or press the
ON Button 1 on the AVR21ENR1 remote. The AVR should turn
on and the lights should turn on or change scenes.
To test the Off function, either press the
Standby/On Button 1
on the AVR’s front panel; or press the Off Button 0 on the
AVR21ENR1 remote. The AVR should turn off and the lights
should turn off or change scenes.
To test the Lighting commands with Manual Via Remote, turn
the AVR off and manually turn the lights off. Turn the AVR on
by pressing the
Standby/On Button 1 on the AVR’s front panel
or press the
On Button 1 on the remote. (The AVR should be on,
but the lights should still be off.) Press the
Trigger Button
on the remote. The lights should turn on or change scene. Press
the
Trigger Button again and the lights should turn off or
change scenes.
Exit Setup
If no further programming is required, press the AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to
return to normal operational mode.
Curtain Control
To open and close a curtain with the AVR turn-on/turn-off functions,
press the
Menu Button on the remote to bring the MAIN
MENU to the screen. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at the REMOTE CONTROL SETUP line.
Press the
Set Button H. The REMOTE CNTL SETUP 1
screen will appear. Press the
⁄
/
¤
Navigation Button F so that
the cursor is pointed at GO TO REMOTE CNTL 2. Press the
Set Button H. The REMOTE CNTL SETUP 2 screen will
appear. Press the
⁄
/
¤
Navigation Button F so that the cursor is
pointed at the CURTAIN CONTROL line. Press the
Set Button
H
. The CURTAIN CONTROL SETUP screen will appear.
Carrier
With the cursor positioned next to CARRIER, press the
‹
/
›
Navigation Button F to select the proper setting. NOTE: Most
IR remotes used with common-source components will have a
carrier, so YES should be selected as a first test. Some cable box
remotes do not use a carrier so, if a code setting doesn’t work,
try changing this setting.
76
System Setup
To Next Page
Loading...