Figure 67.
Zone Setup Page 2
Keypad Setup by Number
Keypad Setup configures each keypad (zone) for how each keypad
will interact with the rest of the system. This setup determines
which groups, if any, a zone will be a part of. If a zone has a video
camera in it, that camera will be “assigned” in this setup for the
purpose of Zone Video Monitoring from other zones. Doorbell,
Talk and Open functions are also configured in this section.
Keypad Setup can be executed from two menu options, Setup
by Number and Setup by Name. For initial configuration, it is
recommended that the Setup by Number menu be used. This
option allows naming the individual zones. Once the zones have
been named, the menus are identical, so choice of Setup by
Number or Name becomes a matter of personal preference.
Figure 68.
Zone Setup By Number Page 1
Page 1
Zone Number
This is the default number assigned to a keypad (zone) by the
system given which
KP (1-20) Keypad Terminal is connected
to on an AVH21. Keypads connected to AVH #1 will be Zones 1–7,
keypads connected to AVH21 #2 will be Zones 8–14 and keypads
connected to AVH #3 will be Zones 15–20. This number cannot be
changed.
Name
Naming the zones serves multiple purposes. In Setup, it provides a
way of knowing which zone is being configured by name (Living
Room, Bedroom 1, etc.) rather than trying to keep track of which
zone is which number. In operational mode, the purpose is similar,
in that the zone names will be displayed on the keypads in various
menus (Paging, Monitoring, etc.) and makes system operation easier
by having menu selections by zone name.
Name Doors
Naming doors populates the KP21 Keypad Door submenu with
names of the door options for Talk and Open. The system default
will show two doors for each AVH21 on the network. A system
with one AVH21 will show Door 1 and Door 2 by default. A system
with two AVH21’s will also show Door 3 and Door 4 in the Door
submenu. A system with three AVH21’s will include Door 5 and
Door 6. By naming the doors, they will appear as
FRONT, REAR,
GARAGE, etc., to make system operation easy without having to
keep track of which door is where.
Figure 66.
Name Doors Screen
To name Doors:
1. From ZONE SETUP PAGE 1, with the cursor next to NAME
DOORS, press the
Set Button H. The NAME DOORS screen
will appear (
Figure 66).
2. Press the
⁄
/
¤
Navigation Button F to position the cursor next
to NAME. Press the
Set Button H. A white rectangle will flash
to the right of NAME: indicating that the remote can be used
to enter the letters for the camera name.
3. Using either the
⁄
/
¤
Navigation Button F or the
Alphanumeric Buttons , enter the first letter for the group
name (e.g., Front). When the first letter appears on screen,
press the
›
Navigation Button F to move the cursor to the
next letter position.
4. Repeat Steps 2–3 above until the Door Name has been spelled
out. A Door Name can have up to five letters. Press the
Set
Button H
. This will store the name and return the cursor back
to the arrow next to NAME.
5. To name additional groups, press the
⁄
/
¤
Navigation Button
F
to position the cursor next to GROUP. Press the
‹
/
›
Navigation Button F to select another group.
6. Repeat Steps 2–4 until all desired Doors have been named.
Up to two doors per AVH21, as described above, can be named,
matching the number of door latch relays on the AVH21s.
To exit Setup, press the
Exit Button G. To continue Zone Setup,
position the cursor next to BACK TO ZONE SETUP and press
the
Set Button H. ZONE SETUP PAGE 1 will appear. Press
the
⁄
/
¤
Navigation Button F to position the cursor next to
GO TO ZONE PAGE 2. Press the
Set Button H. The ZONE
SETUP PAGE 2 screen will appear (
Figure 67). Press the
⁄
/
¤
Navigation Button F to position the cursor next to ZONE
SETUP BY NUMBER. Press the
Set Button H. The SETUP
BY NUMBER PAGE 1 screen will appear (
Figure 68).
To Next Page
Loading...