Sources
The first step is to configure each input. Once an input is
configured, the selection of an input will automatically recall
those settings from a nonvolatile memory. For that reason, the
procedures described below must be repeated for each input
source so that you have the opportunity to customize each source
to your specific listening and viewing requirements. However,
once made, they need not be changed again unless you need to
alter a setting. When using the full-OSD system to make the setup
adjustments, on the remote, press the
AVR Button 4 once
followed by the
Menu Button so that the MAIN MENU
appears.
In MAIN ROOM SETUP, using the
⁄
/
¤
Navigation Button F,
align the cursor with SOURCES. Press the
Set Button H. In the
ARE YOU SURE YOU WANT TO CHANGE ? window, press
the
⁄
/
¤
Navigation Button F, to align the cursor with YES.
Press the
Set Button H. The SOURCES 1 screen will appear
(
Figure 40). Press the
⁄
/
¤
Navigation Button F until the
desired input name appears.
As you scroll through the list of inputs, you may notice that the
video will occasionally switch to black, and you will hear a slight
click. This is normal and does not indicate any problem with the
AVR21EN. When the video turns to black, that is your indication
that the processor has momentarily muted the signal while the
proper video settings for each input are reestablished by the
Faroudja processor. The clicking noise is caused by the use of a
relay to switch between the component video inputs for the
highest signal quality and to minimize video crosstalk.
Figure 40.
Sources 1 Screen
Source Name
When any input is selected as the source, you have the option of
changing the name that appears in the on-screen and front-panel
messages. This allows you to associate a specific product brand or
other name with the input, or to simply enter any name that will
help you to remember which source is being selected.
To change the input name, press the
⁄
/
¤
Navigation Button F
on the remote so that the cursor is pointing to NAME. Next, press
the
Set Button H until a flashing box appears to the right of the
colon. Immediately release the
Set Button H, as you are now
ready to enter the device name.
Press the
⁄
/
¤
Navigation Button F and a complete set of alpha-
numeric characters will be available with the start of the alphabet
in capital letters, followed by the lowercase letters and then num-
Clock Setup
When the Main Menu Appears, the first item to be set is the system
clock. The cursor will be next to the CLOCK SETUP line. Press
the
Set Button H and CLOCK SETUP (Figure 38) will appear
on the screen.
Figure 38.
Clock Setup
With the cursor next to HOUR, press the
⁄
/
¤
Navigation Button
F
to set HOUR. Press the
⁄
/
¤
Navigation Button F to move
the cursor to MINUTE. Repeat these two steps until AM/PM,
YEAR, MONTH, DAY and DAYLIGHT SAVINGS have been
set to local time. When finished, press the
⁄
/
¤
Navigation Button
F
to move the cursor to BACK TO MAIN MENU. Press the
Set Button H. The Main Menu will appear.
Main Room Setup
In the OSD Main Menu, press the
⁄
/
¤
Navigation Button F to
move the cursor next to MAIN ROOM SETUP. Press the
Set
Button H
to select the Main Room Setup.
Figure 39.
Main Room Setup Screen
System Configuration
The System Configuration setting sets the AVR for the particular
speaker configuration being used. With the cursor next to
SYSTEM CONFIGURATION, press the
Set Button H. The
System Configuration Menu will appear. Using the
⁄
/
¤
Navigation
Button F
, align the cursor to 5.1 CHANNEL if using a
Front/Rear/Sub speaker configuration, or 7.1 CHANNEL if using
a Front/Side/Rear/Sub speaker configuration, and press the
Set
Button H
. Select YES in the ARE YOU SURE YOU WANT
TO CHANGE ? window. The System Configuration Menu will
appear. Using the
⁄
/
¤
Navigation Button F, align the cursor
with BACK TO MAIN ROOM. Press the
Set Button H. The
MAIN ROOM SETUP will appear.
To Next Page
Loading...