Navigation Button F until ENABLED appears in the display.
Press the
Set Button H. SAVING will appear briefly in the remote
display and then SAVED will flash four times. The HT Master Enabled
configuration is now set and the remote will automatically return
to operational mode.
Press the TV button on the remote. TV should appear in the
remote display. Press the
On Button 1 on the remote. The
TV/projector just configured should turn On. Press the
Off Button
0
on the remote. The TV/projector should turn off. NOTE: If the
TV/projector does not respond, be sure an IR emitter is properly
connected to the
Control Out All Jack on the AVR’s rear panel
and is properly attached to the TV/projector.
To return to normal operation mode, press the
AVR Button 4
on the AVR21ENR1 remote.
Screen Control
To drop and raise a projection screen with the AVR’s turn-on/turn-
off functions, press the
Menu Button on the remote to bring
the MAIN MENU to the screen. Press the
⁄
/
¤
Navigation Button
F
so that the cursor is pointed at the REMOTE CONTROL
SETUP line. Press the
Set Button H. The REMOTE CNTL
SETUP 1 screen will appear. Press the
⁄
/
¤
Navigation Button
F
so that the cursor is pointed at GO TO REMOTE CNTL 2.
Press the
Set Button H. The REMOTE CNTL SETUP 2 screen
will appear. Press the
⁄
/
¤
Navigation Button F so that the cur-
sor is pointed at the SCREEN CONTROL line. Press the
Set
Button H
. The SCREEN CONTROL SETUP screen will appear.
Carrier
With the cursor positioned next to CARRIER, press the
‹
/
›
Navigation Button F to select the proper setting. NOTE: Most
IR remotes used with common-source components will have a
carrier, so YES should be selected as a first test. Some cable box
remotes do not use a carrier so, if a code setting doesn’t work,
try changing this setting.
Invert Code
Press the
⁄
/
¤
Navigation Button F to move the cursor next to
INVERT CODE. Press the
‹
/
›
Navigation Button F to select
YES/NO. Most devices will be set to NO. Certain devices (Sony
S-Link, Harman Kardon remote control In) will require a YES
setting. Try changing this setting if a specific code selection does
not work for a given device.
Program Code
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the PROGRAM CODE line. Press the
Set Button H. The
SCREEN CODE PROGRAM screen will appear.
Screen Program Code (Manual)
Press the
⁄
/
¤
Navigation Button F so that the cursor is pointed
at the MANUAL line. Press the
Set Button H. The SCREEN
MANUAL PROG screen will appear. SOURCE TYPE will be fixed
as selected (SCREEN).
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to BRAND. Press the
‹
/
›
Navigation Button F to select the
appropriate brand.
Press the
⁄
/
¤
Navigation Button F to move the cursor next
to TRY CODES. With the AVR21ENR1 Main Room remote
selected device type commands until the unit turns off. When the
unit turns off, press the
¤
Navigation Button F to move the
cursor next to YES. Press the
Set Button H to “save” the code
group. This will set this code group for ON/OFF control of the
TV/projector.
If no further programming is required, press the
AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to return
to normal operation mode.
To continue in setup, press the
¤
Navigation Button F to move
the cursor next to BACK TO T/P CODE PROG. Press the
Set Button H. Press the
¤
Navigation Button F again to
move the cursor next to BACK TO T/P CNTL SETUP.
Press the
Set Button H. The TV/PROJ CONTROL SETUP
screen will appear.
To program SCREEN UP/DOWN, LIGHTING ON/OFF,
CURTAIN OPEN/CLOSE, press the
⁄
/
¤
Navigation Button
F
to move the cursor next to BACK TO REM CNTL SETUP.
Press the
Set Button H. See the Screen Control and Lighting
Control
sections.
If a particular brand or functional codes from a source type
cannot be found in the onboard IR code Library, IR commands for
TV/projector On/Off can be taught to the AVR from the original
equipment remote. To teach TV/projector On/Off codes to the
AVR, proceed to the
LEARN CODE section.
TV/Proj Program (Learn Code)
To teach the AVR21EN TV/Projector ON/OFF codes, in the
TV/PROJ CONTROL SETUP screen, press the
¤
Navigation
Button F
to move the cursor next to LEARN CODE. Press the
Set Button H. The TV/PROJ CODE LEARN screen will appear.
With the cursor positioned next to the USING THE
‹›
KEYS
line, press the
Set Button H. The message: USING THE
‹›
KEYS SELECT FUNCTION TO BE PROG will start to flash,
indicating a function can be selected for learning. Press the
‹
Navigation Button F to select TV/PROJ POWER ON.
When the ON function appears, press the
¤
Navigation Button
F
to position the cursor next to POINT ORIGINAL REM
TO AVR DISPLAY PRESS KEY. Press the
Set Button H.
The POINT ORIGINAL message will start to flash. Point
the original remote at the
IR Sensor in the Information
Display O
on the AVR front panel and press the button with the
original code until the message stops flashing and CODE
LEARNED appears on screen.
The cursor will automatically return to the USING THE
‹›
KEYS line. Repeat steps above to program the Off command.
If CODE NOT LEARNED appears, try to learn the code again.
It may be a good idea to replace the original remote’s batteries to
improve signal output from the remote. In some cases, there will
be codes that the AVR just is not capable of learning. Contact the
Audioaccess Technical Service Department for advice if necessary.
Test TV/Projector Code
To test the TV/PROJ ON/OFF commands the AVR21ENR1
remote must be configured for HT MASTER ON/OFF ENABLED.
Press and hold the
Rem Menu Button on the remote until the
Set Button H lights red. Press the
⁄
Navigation Button F
TWICE so HT MASTER ON/OFF shows in the remote’s LCD
Information Display. Press the
Set Button H. Press the
⁄
/
¤
72
System Setup
To Next Page
Loading...