Source
This setting will determine which source the Wake-Up Group will
turn on to. LAST will have each zone in the group turn on to the
last source selected in each of those zones. LOCAL will have each
zone in the group turn on to the local source connected to the
AUX-IN on the KP21 keypads in each of those zones.
Selecting one of the common sources, Disc 1, Disc 2, Disc 3, Radio 1,
Radio 2, A/V/Aux, Video Recorder or Cable/Sat, will have all zones
in the group turn on to that source.
To set Source:
1. In the WAKE-UP SETUP 1-1 screen, press the
⁄
/
¤
Navigation Button F to move the cursor next to SOURCE.
2. Using the
‹
/
›
Navigation Button F, select the source that
the group being configured is to wake up to LAST, LOCAL,
DISC 1, DISC 2, DISC 3, RADIO 1, RADIO 2, A/V/AUX, VIDEO
RECORDER, CABLE/SAT.
3. To continue Setup, press the
⁄
/
¤
Navigation Button F to
position the cursor next to GO TO WAKE-UP 1 PAGE 2.
Press the
Set Button H. The WAKE-UP SETUP 1-2 screen
will appear (
Figure 73).
Figure 73.
Wake-Up Setup 1-2
Wake-Up Group
Reference only. Not configurable in this screen.
Volume Setting
This setting configures the volume that all zones in the group
being configured will turn on at. Consider the use of Wake-Up
Groups when setting this level. Wake-Up for alarm clock purposes
should be loud enough to wake someone up but without startling
him or her or disturbing other zones. Also, a Wake-Up Group set
for dinner-time background music should be set as exactly that –
background music.
To configure Volume Setting:
1. In the WAKE-UP SETUP 1-2 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to VOLUME
SETTING.
2. Using the
‹
/
›
Navigation Button F, set the turn-on volume
that the group being configured is to turn on at, ranging from
–10 to –50dB.
Local Control
This setting will determine whether the individual zone’s keypads
will have the ability to override the Group settings.
To configure Local Control:
1. In the WAKE-UP SETUP 1-2 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
LOCAL CONTROL.
2. Using the
‹
/
›
Navigation Button F, set the keypads in the
group being configured:
YES/NO.
To change settings in WAKE-UP 1 PAGE 1, position the
cursor next to
GO TO WAKE-UP 1 PAGE 1 and press the
Set Button H. Make changes as desired.
To set a second Wake-Up time for the Group currently being
configured, position the cursor next to
GO TO WAKE-UP 2.
Press the
Set Button H and follow previous instructions, starting
at
WAKE-UP GROUP.
To exit the menu and return to system mode, press the
Exit
Button
G
. To continue Zone Setup, position the cursor next to
BACK TO SETUP BY NO. Press the
Set Button H. The
SETUP BY NUMBER PAGE 3 screen will appear. Press the
⁄
/
¤
Navigation Button F to position the cursor next to SLEEP
GROUP. Press the
Set Button H. Proceed to the next section.
Sleep Group
This setting assigns the zone being configured to a Sleep Group.
A Sleep Group is a group of zones that have been configured to
turn off at a specific time. Each zone has the option to be a part
of a Sleep Group (1–8) or not (NONE). All zones set to the same
Group number will turn off together. Each Sleep Group can have
two Sleep Times.
NOTE: Zones can also be configured manually for
individual Sleep functions, when desired.
To assign a zone to a Sleep Group:
1. In the SETUP BY NUMBER PAGE 3 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
SLEEP GROUP.
2. Using the
‹
/
›
Navigation Button F, select the Sleep Group
for the zone being configured: NONE, 1, 2, 3, 4, 5, 6, 7, 8.
3. Using the
⁄
/
¤
Navigation Button F position the cursor next
to SET SLEEP TIMES. Press the
Set Button H. The
SLEEP SETUP 1-1 screen will appear (
Figure 74).
Figure 74.
Sleep Setup 1-1
Sleep Setup 1-1
This submenu sets the parameters for each Sleep Group. These
settings affect the entire group, but do not affect manual Sleep
settings set from the zone keypads.
To Next Page
Loading...