Duration
This setting determines how long the Wake-Up Group will stay on.
The range is 1–30 minutes in 1-minute increments, with an addi-
tional option of UNTIL OFF, which will leave the zones within
the group on until they are turned off individually.
To set Duration:
1. In the WAKE-UP SETUP 1-1 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
DURATION.
2. Using the
‹
/
›
Navigation Button F, set the length of time
in minutes that the group being configured is to stay on.
Select UNTIL OFF to allow the zones within the group to
turn off individually.
When
This setting will configure which day or days of the week the
group being configured will “wake up.” Wake-Up can be set for
Daily, Weekdays, Weekends, Custom, Never or Today. The custom
setting allows selecting the specific days of the week that a group
is to “wake up.”
To configure When:
1. In the WAKE-UP SETUP 1-1 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to WHEN.
2. Using the
‹
/
›
Navigation Button F, select the day(s) that
the group being configured is to “wake up:” Daily, Weekdays,
Weekends, Custom, Never or Today.
3. To configure a custom schedule, with the cursor next to
WHEN,
press the
‹
/
›
Navigation Button F until CUSTOM appears
on screen. Press the
Set Button H. The CUSTOM WAKE-UP
TIME 1
screen will appear (
Figure 72).
Figure 72.
Custom Wake-Up Time 1
4. With the cursor positioned next to MON, press the
‹
/
›
Navigation Button F to set YES/NO. YES will have the
group wakeup on Mondays,
NO will not have the group wakeup
on Mondays. When
MON has been configured, press the
⁄
/
¤
Navigation Button F. Then press the
¤
Navigation Button
F
to move to the next day and/or to the previous day.
5. Repeat Step 4 until all days have been configured for the custom
wake-up setting. Press the
Set Button H to store the custom
setting.
6. Use the
⁄
/
¤
Navigation Button F to position the cursor next
to GO TO WAKE-UP PAGE 1-1. Press the
Set Button H.
Continue Wake-Up Setup.
3. Using the
⁄
/
¤
Navigation Button F position the cursor next
to SET WAKE-UP TIMES. Press the
Set Button H. The
WAKE-UP SETUP 1-1 screen will appear (
Figure 71).
Figure 71.
Wake-Up Setup 1-1
Wake-Up Setup 1-1
This submenu sets the parameters for each Wake-Up Group.
These setting affect the entire group, but do not affect manual
Wake-Up settings set from the zone keypads.
Wake-Up Group
This indicates the Group being configured. Wake-Up Group is not
selectable in this screen. The Group is selected in the SETUP BY
NUMBER PAGE 3 screen on the WAKE-UP GROUP line.
To select a Wake-Up Group:
1. Press the
⁄
/
¤
Navigation Button F to position the cursor next
to BACK TO SETUP BY NO. Press the
Set Button H.
2. In the SETUP BY NUMBER PAGE 3 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to WAKE-UP
GROUP.
3. Using the
‹
/
›
Navigation Button F, select the group to be
configured: 1, 2, 3, 4, 5, 6, 7, 8.
4. Press the
⁄
/
¤
Navigation Button F to position the cursor next
to SET WAKE-UP TIMES. Press the
Set Button H.
Wake-Up Time
This setting assigns the time that the group being configured will
turn on. This setting affects all zones in the group.
To set Wake-Up Time:
1. In the WAKE-UP SETUP 1-1 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to WAKE-UP
TIME 1. Press the
Set Button H. The HOUR field will start
to flash.
2. Using the
⁄
/
¤
Navigation Button F, select the HOUR that the
group being configured is to turn ON.
3. Press the
›
Navigation Button F. The MINUTE field will start
to flash.
4. Using the
⁄
/
¤
Navigation Button F, select the MINUTE that
the group being configured is to turn on.
5. Press the
›
Navigation Button F. The AM/PM field will start
to flash.
6. Using the
⁄
/
¤
Navigation Button F, select AM or PM for the
turn-on time for the group being configured.
7. Press the
Set Button H to store the Wake-Up Time.
To Next Page
Loading...