Camera Assigned
This setting will associate a video camera installed in a particular
zone and connected to one of the
Camera Inputs on an
AVH21 with the Video and Audio/Video Monitoring of the zone
being configured. To illustrate, if the camera installed in the baby’s
room (for example, Zone 4) is connected to
CAM 4 on the
AVH21, or AVH21 #1 in systems using multiple AVH’s, when Zone 4
is being configured, Camera 4 (4) should be selected for this set-
ting. There are 7 camera inputs available for monitoring and there
is a NONE option if a zone does not have a camera installed.
To set Camera Assigned:
1. In the SETUP BY NUMBER PAGE 2 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
CAMERA ASSIGNED.
2. Using the
‹
/
›
Navigation Button F, select the camera for the
zone being configured: NONE, 1, 2, 3, 4, 5, 6, 7.
To exit Setup, press the
Exit Button G. To continue Zone Setup,
position the cursor next to DOOR RING and continue to the
next section.
Door Ring
Future feature.
Door Answer
This setting will determine whether the zone being configured will
have the ability to “talk” to a selected two-way door panel. When
the DOOR button is pressed in the KP21 keypad Main Menu, a list
of available Doors will appear. Selecting a given door then gives
the option to TALK to the door panel or OPEN the door lock
with an associated AVH21 Door Relay. If Door Answer is ENABLED
in a zone, pressing and holding the
Talk Button will
allow the user to communicate with someone located at the selected
door. If Door Answer is disabled in a zone, the message FEATURE
DISABLED Check Settings will appear in the Information
Display on the keypad in the zone attempting to initiate the Talk
function. Door Answer is also available from the KP21R remote
using the
Answer Button to select a door and the Open
Button
to open a selected door.
To enable/disable Door Answer:
1. In the SETUP BY NUMBER PAGE 2 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
DOOR ANSWER.
2. Using the
‹
/
›
Navigation Button F, select the setting for the
zone being configured: ENABLED or DISABLED.
To exit setup, press the
Exit Button G. To continue Zone Setup,
position the cursor next to GO TO PAGE 3 and press the
Set Button H. SETUP BY NUMBER PAGE 3 will appear.
(
Figure 68) To return to SETUP BY NUMBER PAGE 1,
position the cursor next to GO TO PAGE 1 and press the
Set Button H.
Figure 70.
Zone Setup by Number Page 3
Page 3
Keypad #
Not configurable.
Keypad Name
Not configurable in this screen.
Door Open
This setting will determine whether the zone being configured
will have the ability to activate remote door locks or not. When
the
Door Button is pressed in the KP21 keypad Main Menu,
a list of available Doors will appear. Selecting a given door then
gives the option to TALK to the door panel or OPEN the door
lock with an associated AVH21
Door Trigger Output .
If Door Open is ENABLED in a zone, pressing the selected
Door
Open Button
will activate the selected Door Trigger
Output
and release the remote door latch. If Door
Open is disabled in a zone, the message FEATURE DISABLED
Check Settings will appear in the
Information Display
on the KP21 keypad in the zone attempting to initiate the
Open function.
To enable/disable Door Open:
1. In the SETUP BY NUMBER PAGE 3 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to
DOOR OPEN.
2. Using the
‹
/
›
Navigation Button F, select the setting for the
zone being configured: ENABLED or DISABLED.
Wake-Up Group
This setting assigns the zone being configured to a Wake-Up
Group. A Wake-Up Group is a group of zones that have been
configured to turn on at a specific time, to a specific source, at a
specific volume, for a preset duration. Each zone has the option
to be a part of a Wake-Up Group (1–8) or not (NONE). All zones
set to the same group number will turn on and off together.
Each Wake-Up Group can have two Wake-Up Times.
NOTE: Zones can also be configured manually for individual
Wake-Up functions, when desired.
To assign a zone to a Wake-Up Group:
1. In the SETUP BY NUMBER PAGE 3 screen, press the
⁄
/
¤
Navigation Button F to position the cursor next to WAKE-UP
GROUP.
2. Using the
‹
/
›
Navigation Button F, select the group for the
zone being configured: NONE, 1, 2, 3, 4, 5, 6, 7, 8.
To Next Page
Loading...