104
3. Press the Set Button H to reset the remote. Note that once
the Set button is pressed, the process may not be stopped.
While the remote’s memory is being cleared, a RESETTING...
message will appear in the upper line of the remote’s LCD screen
as shown in
Figure 114. It may take a few minutes for the reset
process to take place, and the length of time will vary, depending
on how much customization and programming has taken place.
Please be patient; as long as the message appears in the display,
the remote is functioning properly.
Figure 114.
4. When the remote has been totally reset and returned to the
factory default condition, a REMOTE RESET COMPLETE
message (
Figure 115) will appear briefly, and then the remote
will return to normal operation.
Figure 115.
Additional Notes on Configuring and Operating
the Remote
I When the remote is being programmed, it will automatically
time-out if no button is pressed within a thirty-second period.
The message shown in
Figure 116 will appear briefly, and the
remote will then exit the feature being programmed, and any
data entered will be lost.
Figure 116.
I The programming or configuration process may also be stopped
at any time by pressing the
Rem Menu Button . The
message shown in
Figure 117 will appear, the data entered in
the current process will be lost and the remote will return to
normal operation. Any process that was underway when the
button is pressed must be restarted.
I Extensive use of the programming, learning and configuration
functions of the remote may consume significantly more battery
power than normal remote operation. While the batteries
should last for four to six months in normal operation, you may
find that they need to be changed sooner, after the remote is
programmed for the first time.
I When the batteries approach a level below which the remote
will not function, the remote’s LCD screen will display a
LOW BATTERY warning, as shown in
Figure 117. We strongly
recommend replacing the batteries as soon as this message
appears to avoid the loss of programming and configuration
settings. These settings are not lost when the batteries are
changed quickly.
AVR21ENR1 Remote Control
3. At the next menu screen, press the
⁄
/
¤
Navigation Button F
until the bottom line in the remote’s LCD shows READ A
MACRO. Press the
Set Button H to begin the process of
reading a macro (
Figure 111).
Figure 111.
4. The next display screen (Figure 112) is where you select the
macro to be read. Press the
⁄
/
¤
Navigation Button F until
the name of the macro you wish to read appears. For this
example, we will read back Macro 1, created in a previous
section. When the name of the macro to be read appears,
press the
Set Button H.
Figure 112.
5. As soon as the Set Button H is pressed, the first two steps in
the macro will appear in the remote’s LCD screen. You may then
use the
⁄
/
¤
Navigation Button F to step up or down through
the list of commands stored as the macro. As you read the
display, you will see
Input Selector Buttons 3 appear in
brackets (e.g., [AVR]). When the step in the macro is a function,
navigation or any other button, it will appear next to the
bracketed readout of the underlying device (e.g., [AVR]
POWER ON).
6. When you are finished reviewing the macro’s contents, press the
Set Button H to return the remote to normal operation.
Resetting the Remote
Depending on the way in which the remote has been programmed,
there may be a situation in which you wish to totally erase all
changes that have been made to the remote and return it to the
factory defaults. You may do that by following the steps shown
below, but remember that once the remote is reset, ALL changes
that have been made (including programming for use with other
devices, learned keys, macros, settings and key names) will be
erased, and any settings you had previously made will have to be
reentered. To erase all settings and reset the remote to the original
factory default settings and displays, follow these steps:
1. Press and hold the
Rem Menu Button for about 3 seconds
while the message HOLD BUTTON FOR 3 SECONDS appears
in the remote’s LCD
Information Display 2. Release the but-
ton when the red light under the
Set Button H appears.
2. The remote’s MAIN MENU message will appear in the LCD
and the
Set Button H will remain illuminated in red. Press
the
⁄
/
¤
Navigation Button F until USER RESET appears on
the bottom line of the LCD screen, as shown in
Figure 113.
Figure 113.
To Next Page
Loading...