Figure 76.
Sleep Setup 1-2
Sleep Group
Reference only. Not configurable in this screen.
Volume Setting
This setting configures the volume that all zones in the group
being configured will change to when Sleep Time is reached.
To configure Volume Setting:
1. In the SLEEP SETUP 1-2 screen, press the
⁄
/
¤
Navigation
Button F
to position the cursor next to VOLUME SETTING.
2. Using the
‹
/
›
Navigation Button F, set the sleep volume
that the group being configured is to switch to, in the range
of –10 to –50dB.
Local Control
This setting allows an individual zone’s keypad to have the ability
to set Sleep and Wake-Up settings for the local zone.
To configure Local Control:
1. In the SLEEP SETUP 1-2 screen, press the
⁄
/
¤
Navigation
Button F
to position the cursor next to LOCAL CONTROL.
2. Using the
‹
/
›
Navigation Button F, set the keypads in the
group being configured: YES/NO.
To change settings in Sleep 1 Page 1, position the cursor next to
GO TO SLEEP 1 PAGE 1 and press the
Set Button H.
Make changes, as desired.
To set a second Wake-Up time for the Group currently being
configured, position the cursor next to GO TO SLEEP 2.
Press the
Set Button H and follow previous instructions starting
at SLEEP GROUP.
To make changes or to confirm settings in Zone Setup, position
the cursor next to BACK TO ZONE SETUP or GO TO PAGE
2. Press the
Set Button H. Use the
⁄
/
¤
/
‹
/
›
Navigation Buttons
F
to review Setup Pages and Settings. Make changes as neces-
sary. Refer to previous instructions. Confirm system functions from
zones using keypads.
To exit the menu and return to system mode, press the
Exit Button G.
Keypad Setup by Name
Keypad Setup by Name allows zone configuration when searching
by Zone Name.
NOTE: The correct DIP Switch setting must be set
on the KP21. The number on the KP21 DIP Switch should match
the connection on the AVH21. Please see
KP21 Connections section
for correct settings. Zone Name can only be edited in Keypad
Setup by Number.
To make changes to zone settings in KEYPAD SETUP BY NAME:
1. In the Main Room, turn on the AVR21EN and Main Room
video display.
2. Press the
AVR Button 4 on the AVR21ENR1 remote.
3. Press the
Menu Button on the remote. The MAIN MENU
will appear.
4. Press the
¤
Navigation Button F until the cursor is next to:
ZONE SETUP.
5. Press the
Set Button H. ZONE SETUP PAGE 1, will appear.
6. Make changes in ZONE SETUP PAGE 1 as described in
Zone Setup.
7. To enter ZONE SETUP BY NAME, use the
⁄
/
¤
Navigation
Button F
to position the cursor next to GO TO ZONE
PAGE 2. Press the
Set Button H.
8. Use the
⁄
/
¤
Navigation Button F to position the cursor next
to ZONE SETUP BY NAME. Press the
Set Button H.
9. Use the
‹
/
›
Navigation Button F to select the zone to be
configured, by name.
10. Follow the instructions in the
Keypad Setup by Number section.
Diagnostics
The Diagnostics screens provide real-time system information
regarding which W.H.E.N. system components are connected and
the firmware versions in the components found.
To open the Diagnostics Menu:
1. In the Main Room, turn on the AVR21EN and main room video
display.
2. Press the
AVR Button 4 on the AVR21ENR1 remote.
3. Press the
Menu Button on the remote. The MAIN MENU
will appear.
4. Press the
¤
Navigation Button F until the cursor is next to
DIAGNOSTICS.
5. Press the
Set Button H. The DIAGNOSTICS screen will
appear (
Figure 77).
Figure 77.
Diagnostics Main Menu
Settings
These screens show that the main system components and the
AVR21EN and AVH21 A/V hubs are connected, powered up and
functional. The values associated with each line item refer to
software and firmware versions and are primarily intended for use
To Next Page
Loading...