Lighting Program Code (Automatic)
If On/Off codes could not be found by Brand in the Manual mode,
try searching by source type in the Automatic mode.
At the LIGHTING CODE PROGRAM screen, press the
⁄
/
¤
Navigation Button F to move the cursor next to AUTOMATIC.
Press the
Set Button H. The LIGHTING AUTO PROGRAM
screen will appear.
The SOURCE will be fixed as selected (LIGHTING). Press the
¤
Navigation Button F to move the cursor next to TRY CODES.
Repeatedly press the
‹
or
›
Navigation Button F to test all
selected device type commands until the unit turns off. When the
unit turns off, press the
¤
Navigation Button F to move the
cursor next to YES. Press the
Set Button H to “save” the code
group. This will set this code group for On/Off control lighting.
If no further programming is required, press the
AVR Button 4
on the AVR21ENR1 remote and then the Exit Button G to return
to normal operational mode.
To continue in setup, press the
¤
Navigation Button F to move
the cursor next to
BACK TO LGT CODE PROG. Press the
Set
Button
H
. Press the
¤
Navigation Button F again to move
the cursor next to
BACK TO LGT CNTL SETUP. Press the
Set Button H. The LIGHTING CONTROL SETUP screen
will appear.
To program TV/PROJECTOR ON/OFF, SCREEN ON/OFF,
CURTAIN OPEN/CLOSE, press the
⁄
/
¤
Navigation Button
F
to move the cursor next to BACK TO REM CNTL SETUP.
Press the
Set Button H. See the TV/Projector, Screen and
Curtain sections.
If a particular brand or functional code from a source type cannot
be found in the onboard IR code Library, IR commands for Lights
On/Off, or a particular scene, can be taught to the AVR from the
original equipment remote. To teach Lighting On/Off or scene
codes to the AVR, proceed to the
Learn Code section.
Lighting Program (Learn Code)
To teach the AVR21EN Lighting On/Off codes, in the LIGHTING
CONTROL SETUP screen, press the
¤
Navigation Button F to
move the cursor next to LEARN CODE. Press the
Set Button H.
The LIGHTING CODE LEARN screen will appear.
With the cursor positioned next to USING THE
‹›
KEYS
line, press the
Set Button H. The message USING THE
‹›
KEYS SELECT FUNCTION TO BE PROG will start to
flash, indicating a function can be selected for learning. Press the
‹
Navigation Button F to select LIGHTING POWER ON.
When the ON function appears, press the
¤
Navigation Button
F
to position the cursor next to POINT ORIGINAL REM
TO AVR DISPLAY PRESS KEY. Press the
Set Button H.
The POINT ORIGINAL message will start to flash. Point
the original remote at the
IR Sensor in the Information
Display
O
on the AVR’s front panel and press the button with
the original code until the message stops flashing and CODE
LEARNED appears on screen.If you want to program a lighting
scene change rather than On, program LIGHTING POWER ON
with the IR command for the Main Room regular lighting scene.
The cursor will automatically return to the USING THE
‹›
KEYS line. Repeat steps above to program the OFF command.
If you want to program a lighting scene change rather than Off,
program LIGHTING POWER OFF with the IR command for
the “Movie Mode” lighting scene.
If CODE NOT LEARNED appears, try to learn the code again.
It may be a good idea to replace the original remote’s batteries to
improve signal output from the remote. In some cases, there will
be codes that the AVR just is not capable of learning. Contact the
Audioaccess Technical Service Department for advice, if necessary.
Test Lighting Code
To test the Lighting On/Off commands the AVR21ENR1 remote
must be configured for HT Master On/Off Enabled.
Press and hold the
Rem Menu Button on the remote until the
Set Button H lights red. Press the
⁄
Navigation Button F
twice so HT MASTER ON/OFF shows in the remote’s LCD
Information Display 2. Press the Set Button H. Press the
⁄
/
¤
Navigation Button F until ENABLED appears in the display.
Press the
Set Button H. SAVING will appear briefly in the
remote upper display line and then SAVED will flash four times.
The HT Master Enabled configuration is now set and the remote
will automatically return to operational mode.
Press the
TV Button 5 on the remote. TV should appear in the
remote upper display line. Press the
On Button 1 on the remote.
The Lighting just configured should turn on or change scene. Press
the
Off Button 0 on the remote. The Lighting should turn off or
change scene.
NOTE: If the Lighting system does not respond, be
sure an IR emitter is properly connected to the
Control Out All
Jack
on the AVR’s rear panel and is properly attached to the
Lighting Controller.
To return to normal operational mode press the
AVR Button 4
on the AVR21ENR1 remote.
Voltage Trigger (Lighting)
The Trigger Out Jack on the AVR’s rear panel can be controlled
in two modes:
AVR On/Off: Simply put, when the AVR turns on, the Trigger Out
Jack
outputs a constant +12V DC control voltage. In this case,
with the
Trigger Out Jack being used to turn lights on or set
a lighting scene when the AVR is turned on. When the AVR is
turned off, the
Trigger Out Jack drops to 0V DC, and the lights
turn off or switch to a different scene.
NOTE: If the AVR turns on
to Multiroom mode, the
Trigger Out Jack will stay at 0V DC
until the Main Room is turned on.
Manual Via Remote: In this mode, the Trigger Out Jack is
controlled with the
Trigger Button on the AVR21ENR1
remote. When the AVR is turned on, the
Trigger Out Jack has
an output of 0V DC. When the
Trigger Button on the remote
is pressed, the
Trigger Out Jack goes to +12V DC, in this case,
to turn the lights on or set a scene. Press the
Trigger Button
again; the voltage is cut and the lights turn off or switch to a
different scene.
To configure the AVR21EN
Trigger Out Jack to control lighting
when the Main Room is turned on:
Press the
Menu Button on the remote to bring the MAIN
MENU to the screen. Press the
⁄
/
¤
Navigation Button F so
that the cursor is pointed at the REMOTE CONTROL SETUP
line. Press the
Set Button H. The REMOTE CNTL SETUP 1
75
System Setup
To Next Page
Loading...