AudioCodes Mediant 1000 User Manual

Version 7.2 1057 Mediant 1000B Gateway & E-SBC
User's Manual 62. Configuration Parameters Reference
Parameter Description
MWI Server Transport Type
configure voip > gateway dtmf-
supp-service supp-service-
settings > mwi-srvr-transp-type
[MWIServerTransportType]
Determines the transport layer used for outgoing SIP dialogs
initiated by the device to the MWI server.
 [-1] Not Configured (default)
 [0] UDP
 [1] TCP
 [2] TLS
Note: When set to ‘Not Configured’, the value of the parameter
SIPTransportType is used.
MWI Subscribe Expiration Time
configure voip > gateway dtmf-
supp-service supp-service-
settings > mwi-subs-expr-time
[MWIExpirationTime]
Defines the MWI subscription expiration time in seconds.
The default is 7200 seconds. The range is 10 to 2,000,000.
MWI Subscribe Retry Time
configure voip > gateway dtmf-
supp-service supp-service-
settings > mwi-subs-rtry-time
[SubscribeRetryTime]
Defines the subscription retry time (in seconds) after last
subscription failure.
The default is 120 seconds. The range is 10 to 2,000,000.
Subscription Mode
configure voip > sip-definition
proxy-and-registration >
subscription-mode
[SubscriptionMode]
Determines the method the device uses to subscribe to an MWI
server.
 [0] Per Endpoint = (Default) Each endpoint subscribes
separately - typically used for FXS interfaces.
 [1] Per Gateway = Single subscription for the entire device -
typically used for FXO interfaces.
configure voip > interface fxs-fxo
> etsi-vmwi-type-one-standard
[ETSIVMWITypeOneStandard]
Determines the ETSI Visual Message Waiting Indication (VMWI)
Type 1 sub-standard.
 [0] = (Default) ETSI VMWI between rings
 [1] = ETSI VMWI before ring DT_AS
 [2] = ETSI VMWI before ring RP_AS
 [3] = ETSI VMWI before ring LR_DT_AS
 [4] = ETSI VMWI not ring related DT_AS
 [5] = ETSI VMWI not ring related RP_AS
 [6] = ETSI VMWI not ring related LR_DT_AS
Note: For the parameter to take effect, a device reset is required.
configure voip > interface fxs-fxo
> bellcore-vmwi-type-one-
standard
[BellcoreVMWITypeOneStandard]
Determines the Bellcore VMWI sub-standard.
 [0] = (Default) Between rings.
 [1] = Not ring related.
Note: For the parameter to take effect, a device reset is required.
62.10.5.5 Call Hold Parameters
The call hold parameters are described in the table below.
Table 62-46: Call Hold Parameters
Parameter Description

AudioCodes Mediant 1000 Specifications

General

Data link protocols	CAS: MF-R1: T1 CAS, ISDN PRI: ETSI/EURO ISDN, ANSI NI2, QSIG
Security algorithms	HTTPS, SRTP
Authentication method	RADIUS
Internal memory	512 MB
Built-in processor	Celeron 600 MHz
Processor frequency	600 MHz
Internal memory type	-
Number of processors installed	1
Voice codecs	G.711, G.723.1, G.726, G.729A, iLBC
Safety	UL60950-1, FCC 47 CFR
Certification	ETS 300019-2-1, ETS 300019-2-2 ETS 300019-2-3
Mounting type	Rack mounting
LED indicators	Yes
Power requirements	90-260 V AC

Weight and Dimensions

Size (imperial)	19 \