Autonics TK4L - Table of Contents

Table of Contents
x © Copyright Reserved Autonics Co., Ltd.
5.3.3 Changing Parameter Settings .................................................................... 36
5.3.4 MV Monitoring and Manual Control Setting ............................................... 36
5.4 Parameter Reference Chart .............................................................................. 38
5.5 Parameter Setting Groups ................................................................................. 40
5.5.1 Parameter 1 Setting Group [PAR1] ............................................................ 40
5.5.2 Parameter 2 Setting Group [PAR2] ............................................................ 41
5.5.3 Parameter 3 Setting Group [PAR3] ............................................................ 43
5.5.4 Parameter 4 Setting Group [PAR4] ............................................................ 45
5.5.5 Parameter 5 Setting Group [PAR5] ............................................................ 47
6 Parameter Settings and Functions .......................................................... 49
6.1 Input ................................................................................................................... 49
6.1.1 Input Types and Temperature Ranges ....................................................... 49
6.1.2 Input Type Settings [PAR3 → IN-T] ........................................................... 51
6.1.3 Temperature Unit Settings for Input Temperature Sensor [PAR3 → UNIT] 51
6.1.4 Analog Input/Scale Settings ....................................................................... 52
6.1.5 Input Bias Adjustments [PAR3 → IN-B] ..................................................... 54
6.1.6 Input Digital Filter [PAR3 → MAV.F] ............................................................ 54
6.1.7 High and Low-limit of SV (Setting Value) [PAR3 → H-SV/ L-SV] ............... 55
6.2 Control Output ................................................................................................... 56
6.2.1 Control Output Mode [PAR3 → O-FT] ........................................................ 56
6.2.2 MV High / Low-limit Settings [PAR2 → H-MV / L-MV] ................................. 62
6.2.3 Ramp Settings [PAR2 → RAMU/ RAMD/ rUNT] ............................................ 63
6.2.4 Auto/Manual Control Settings .................................................................... 64
6.2.5 Output Settings ........................................................................................... 67
6.3 Temperature Control .......................................................................................... 69
6.3.1 Temperature Control Mode [PAR3 → C-MD] ............................................... 69
6.3.2 On/Off Control [PAR3 → C-MD → ONOF] .................................................... 70
6.3.3 PID Control [PAR3 → C-MD → PID] ........................................................... 71
6.3.4 Auto-tuning ................................................................................................. 75
6.4 Alarm Output ...................................................................................................... 77
6.4.1 Alarm Output Mode [PAR4 → AL-1/AL-2] ................................................. 77
6.4.2 Alarm Output Options [PAR4 → AL!T/AL@T] ............................................. 79
6.4.3 Alarm SV Settings [PAR1 → AL!L/AL!H/AL@L/AL@H] .............................. 80
6.4.4 Alarm Output Hysteresis [PAR4 → A!HY/A@HY] ........................................ 80
6.4.5 Alarm Output Mode Selection [PAR4 → A!N/A@N] ..................................... 81
6.4.6 Alarm Output Delay Settings [PAR4 → A!ON / A!OF/ A@ON / A@OF] ......... 81
6.4.7 Loop Break Alarm [PAR4 → AL-1/AL-2 → LBA] ....................................... 83
6.4.8 Sensor Break Alarm [PAR4 → AL-1/AL-2 → SBA] .................................... 85
6.4.9 Heater Burnout Alarm [PAR4 → AL-1/AL-2 → HBA] ................................. 85
6.4.10 Alarm Output Deactivation [PAR5 → DI-K→ AL.RE] ................................. 87
6.4.11 Alarm Output Examples ............................................................................. 88